manualshive.com logo in svg

Polsen ULW-16, Руководство по эксплуатации продукта, Страница: 10 / 20

Поделиться
Скачать
Polsen ULW-16 Скачать руководство пользователя страница 10

10

 c. 

  Change the channel with short presses of the SELECT button until the desired channel is selected. The channel indicator will 

continue to blink for 10 seconds and then stop indicating that the channel has been selected.

  d.   

Replace the battery compartment cover.

Note

:

 If you are using multiple ULW-16 or ULW-16-HL wireless systems, make sure each system is set to a different channel

—

at 

least three channels apart as a guard band.

3.

   With the headphone volume set to a low level, plug an earpiece or headphones into the receiver and gradually raise the level to 

a comfortable volume for monitoring the transmission.

4.

   Adjust the audio output level on the receiver or the input level on your input device as necessary to make sure a sufficient level 

is being recorded. The objective is to transmit the highest possible level without distortion for the best signal-to-noise ratio 
throughout the signal path.

Important

:

 It is not recommended to adjust the gain setting of the handheld transmitter. The gain is factory preset to the ideal 

setting. Any volume adjustments should be made on the receiver or on the input device.

5.

   Once you have determined that the transmission quality and level are good, 

mount the receiver.

Note

:

 When holding the ULW-16-HHT handheld transmitter, hold it in the middle 

of the transmitter body, not at the end where the antenna is located. Covering the 
antenna with your hand will degrade the transmission quality.

Содержание ULW-16





















Отзывы:

Нет отзывов