Pololu Corporation M2H24v14 Скачать руководство пользователя страница 44

Страница: 44 / 67

Current speed

Category

motor-specific

Offset

Type

signed 16-bit

Range

−800 to 800

Default

Command

Set speed
Set all speeds
Set all speeds using buffers

Arduino library

void setSpeed(uint8_t motor, int16_t speed)

void setSpeedNow(uint8_t motor, int16_t speed)

void setAllSpeeds(int16_t speed1, ...)

void setAllSpeedsNow(int16_t speed1, ...)

void setAllSpeedsUsingBuffers()

void setAllSpeedsNowUsingBuffers()

void getCurrentSpeed(uint8_t motor)

This is the speed that the Motoron is currently trying to apply to the motor.

• A value of 0 means the motor is braking (both outputs driving low), coasting (both outputs

disabled), or something in between, as determined by the

target brake amount

variable

and the hardware limitations of the controller.

• A value of 800 corresponds to the MxA output driving high (VIN) and the MxB output

driving low (GND). This direction is called

forward

, and causes the

green

motor

indicator LED to turn on.

• A value of −800 corresponds to the MxA output driving low (0 V) and the MxB output

driving high (VIN). This direction is called

reverse

, and causes the

red

motor indicator

LED to turn on.

• Intermediate values correspond to rapidly switching the motor outputs between braking

and driving the motor in the specified direction.

Pololu Motoron Motor Controller User’s Guide

8. Variable reference

Page 44 of 67

Содержание M2H24v14




































































Результаты поиска

Содержание M2H24v14

Отзывы:

Pololu Corporation M2H24v14, Руководство пользователя, Страница: 44 / 67

Результаты поиска

Содержание M2H24v14

Отзывы: