Quick installation Guide
http://www.autostart.ca P.5
PROGRAMMING OPTIONS
MODE 1
* INDICATES DEFAULT SETTING
FUNCTION 1 – Ignition-controlled door locks
OPTION 1*
Ignition lock DISABLED
OPTION 2
Ignition lock
ENABLED
OPTION 3
Ignition unlock only
OPTION 4
Ignition lock only
FUNCTION 2 – Secure Lock
OPTION 1*
Secure lock DISABLED
OPTION 2
Standard secure lock
ENABLED
OPTION 3
Smart secure lock
ENABLED
FUNCTION 3 – Starter Kill
OPTION 1*
Passive arming (60 sec.)
OPTION 2
Active arming
OPTION 3
Passive arming (3 min.)
FUNCTION 4 – Door lock / unlock pulse timing
OPTION 1*
7/10-sec. lock / unlock pulses
OPTION 2
4-sec. lock / unlock pulses
OPTION 3
7/10-sec. lock pulse and two ¼ -sec. unlock pulses
OPTION 4
1/10-sec. lock / unlock pulses
FUNCTION 5 – LED flashing
OPTION 1*
ENABLED (will only flash when ignition is OFF)
OPTION 2
DISABLED
OPTION 3
ENABLED
(will only flash when Starter kill engages (depends on Mode 1,
Function 3 programming)
MODE 2
* INDICATES DEFAULT SETTING
FUNCTION 1 – Safe Start
OPTION 1
Safe start
ENABLED
OPTION 2*
Safe start DISABLED
OPTION 3
Swap Start
FUNCTION 2 – Engine Run Time
OPTION 1
Run time = 3 minutes in
gas
mode / 8 minutes
diesel
mode
OPTION 2*
Run time = 15 minutes in gas mode / 20 minutes diesel mode
OPTION 3
Run time = 25 minutes in
gas
mode / 30 minutes
diesel
mode
FUNCTION 3 –Idle Mode & Turbo Mode (auto) / Turbo Mode (manual)
OPTION 1
Idle mode & turbo mode
DISABLED (AUTO)
/ turbo mode
DISABLED (MANUAL)
OPTION 2*
Idle mode & turbo mode ENABLED (AUTO) / turbo mode DISABLED (MANUAL)
OPTION 3
Idle mode & turbo mode
ENABLED (AUTO)
/ turbo mode
ENABLED (MANUAL)
FUNCTION 4 – Engine type and Cold Weather Mode
OPTION 1
Diesel mode with 20-minute run time in cold weather mode (30-sec. wait to start delay)
OPTION 2*
Gas mode with 3-minute run time in cold weather mode
OPTION 3
Diesel mode with 8-minute run time in cold weather mode (18-sec. wait to start delay)
OPTION 4
Diesel mode with 8-minute run time in cold weather mode (7-sec. wait to start delay)
FUNCTION 5 – Disarm option
OPTION 1
Disarm with Ignition, Accessory and Ground Out
OPTION 2*
Disarm only
MODE 3
* INDICATES DEFAULT SETTING
FUNCTION 1 – Home Valet
OPTION 1
Home Valet
ENABLED
OPTION 2*
Home Valet DISABLED
FUNCTION 2 – AUX 1 Programming
OPTION 1
Horn confirmation upon the 2
nd
press of the
LOCK
button
OPTION 2*
Priority door access
OPTION 3
Horn confirmation upon the 1
st
press of the
LOCK
button
OPTION 4
Negative Accessory output
FUNCTION 3 – AUX 2 Programming
OPTION 1
Constant output
OPTION 2*
Toggle ON/OFF (with 30-second time out)
OPTION 3
Toggle ON/OFF (with 4-minute time out)
Æ
active when started remotely
OPTION 4
Negative Starter output
FUNCTION 4 – AUX 3 / TRUNK output
OPTION 1
1-sec. output
P.6 http://www.autostart.ca
Quick Installation Guide
OPTION 2*
Constant output
OPTION 3
Trunk output with disarm and rearm pulses
FUNCTION 5 – External Trigger
OPTION 1
Zone 3 with disarm/rearm (Trunk monitor)
OPTION 2*
Key sense
OPTION 3
Engine Start/Stop
OPTION 4
SmartStart™
MODE 4
* INDICATES DEFAULT SETTING
FUNCTION 1 –
Alarm control
OPTION 1
ENABLED
(HORN must be enabled in MODE 3 FUNCTION 2, option 1 or 3)
OPTION 2
DISABLED
FUNCTION 2 – Ready Mode Option / Hybrid Option
OPTION 1
ENABLED
by handbrake
OPTION 2*
ENABLED by remote
OPTION 3
Hybrid option
ENABLED
FUNCTION 3 – Ready mode completion option
OPTION 1
Open/Close door
OPTION 2*
Remote
OPTION 3
Open/Close door with automatic door-lock
FUNCTION 4 – Bypass
OPTION 1
ADS (2-way D2D)
OPTION 2*
Xpresskit (2-way D2D)
OPTION 3
Fortin (1-way D2D)
FUNCTION 5 – Push-To-Start option
OPTION 1
Push-To-Start
ENABLED
without takeover
OPTION 2*
Push-To-Start DISABLED
OPTION 3
Push-To-Start
ENABLED
with takeover within 1.5 min.
OPTION 4
Push-To-Start
ENABLED
with takeover within 3 min.
HORN ADJUSTMENT
Note: Before adjustment, horn option must be installed and enabled.
1.
In programming mode (page 3).
2.
Press and hold the brake pedal, then simultaneously press the
UNLOCK
and
START
buttons
the
horn will chirp 5 times.
3.
Release the brake pedal.
4.
To change the timing:
1.
To increase the horn pulse by 3 ms, press the
LOCK
button.
2.
To decrease the pulse by 3 ms, press the
UNLOCK
button.
3.
To increase the pulse by 10 ms, press the
START
button.
4.
To decrease the pulse by 10 ms, press the
TRUNK
button.
5.
To save the new settings: press
LOCK
and
UNLOCK
simultaneously. If 3 chirps are returned, the new
setting has been saved.
6.
You have 20 more seconds to select one of the sub-menus if needed.
SETTING UP THE TACH
VIRTUAL TACH ADJUSTMENT
Warning: For automatic transmissions only.
Virtual Tach System combines the latest microcontroller technology and a complex algorithm that took years to
develop. VTS is able to effectively monitor the engine starting sequence and release the starter at the right time
without physically connecting the tach wire to the remote starter. The VTS constantly monitors the data and
readjusts itself automatically in order to maximize its capability to start the engine properly in any weather or
deteriorating battery condition
.
OPTIONAL TIME DELAY ADJUSTMENT IN VIRTUAL TACH SYSTEM
Follow these steps to program crank time adjustment, if needed:
1.
In programming mode (page 3).
Before the lights go out, press and hold the brake pedal and press the
LOCK
and
UNLOCK
buttons
simultaneously
the parking lights will flash 4 times.
Do not release the brake pedal.
