Quick installation Guide
http://www.autostart.ca P.7
2. Press the
LOCK
button if you wish to increase the time delay or the
UNLOCK
button if you want to
decrease it.
The time delay will be increased or decreased by 50 ms and the parking lights will flash
once every time the LOCK or UNLOCK button is pressed.
3. Press the
TRUNK
button to save the settings you have entered.
4. Release the brake pedal – the time delay programming is now complete.
MULTI-SPEED TACH PROGRAMMING (IF INSTALLED)
1.
In programming mode (page 3).
2. Before the lights go out, press and hold the brake pedal and press the
LOCK
and
UNLOCK
buttons
simultaneously
the parking lights will flash 4 times. At that point, release the brake pedal.
3. Start the engine and allow the vehicle to reach regular engine idle speed.
4. Once the engine is running at normal idle speed, press the brake pedal and keep it down until you hear the
parking lights flash 5 times.
5. Release the brake pedal
the tach programming is now complete.
Caution! – Tach jumper settings:
Some new vehicles have a higher TACH voltage threshold, which would fall out of the normal TACH trigger
circuit of the remote car starter. Changing the jumper to TACH Threshold HIGH will allow the module to
properly detect the TACH signal.
BUT
, if you are having trouble with the TACH, please call our tech support
team. Problems requiring changing the TACH jumper settings are very rare.
RESETTING THE MODULE
WARNING!
By resetting the module, all programmed values are erased
i.e.: tach, transmitter as well as
programming options. The programming options are returned to their default values.
1.
Enter programming Mode (page 3).
2. Once having reached the programming mode, quickly press and release the brake pedal until the parking
lights flash 8 times.
BYPASS
Remote starters of this series have the ability to work in two way mode (D2D) with
Xpresskit
and
ADS
bypass
modules. They also offer one way communication with
Xpresskit, ADS
and
Fortin
brand bypass modules.
Note:
For Hardware 5.0 and higher there can only be one bypass connected to the unit.
NEW FEATURE – SMARTSTART™
When teamed up with a SmartStart
™
-compatible module, remote start features can be accessed using a
smartphone. These features include lock/unlock, engine start/stop, trunk release, panic and alarm notifications.
For alarm notifications, the Xpresskit
™
bypass option (D2D) must be enabled.
To use these features, connect the SmartStart
™
module to the SmartStart
™
port located at the back of the
remote start module (see the wiring diagram). The SmartStart
™
feature must be enabled using the
programming options list found in this guide.
PROGRAMMING MODE LOCKED FEATURE
The programming mode locked feature is enabled after a successful initial remote start in EncryptR™ mode.
When this feature is locked, unauthorized access to the following programming mode sub-menus through the
hood pin or the PRG-1000 is denied.
1.
Transmitter learning
2.
Tachometer programming
3.
VTS adjustment
4.
Access to programming options
5.
Horn timing adjustments
How to lock the programming mode
During installation, for the “programming mode locked” feature to take effect, the installer must successfully
remote-start the vehicle.
Programming mode can be locked through the following actions:
1.
Arm the system by pressing lock.
P.4 http://www.autostart.ca
Quick Installation Guide
Warning!
Please note that the wire to wire brake communication is locked once an analog signal is detected on the
remote starter’s brake input. To detect D2D brake again, after being locked in “wire to wire” mode, make sure
no connection is made at the brake input wire, unplug the remote starter’s power and then plug it back in.
PROGRAMMING THE TRANSMITTER TO THE MODULE
1.
In programming mode (page 3)
- the parking lights will stay on for up to 20 seconds.
2.
Before the lights go out, turn the ignition key to
OFF
(if not OFF already), then
ON
, then
OFF
.
3.
Press and hold the
button and keep it down until the parking lights flash
5 times quickly
(unit will
click). The parking lights remain lit for 20 seconds.
4.
The transmitter has been stored in memory. Each unit can store 4 remotes in its memory.
5.
Either close the hood to end the programming procedure or select one of the sub-menus before the lights
turn off.
To program a transmitter on the second vehicle for multi-car operation;
press the
button (instead of
) in step 3 of the transmitter programming procedure.
ENTERING PROGRAMMING OPTIONS
1.
In programming mode (page 3)
the parking lights will stay on for up to 20 seconds.
2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons.
x
LOCK
to access mode 1;
x
UNLOCK
to access mode 2;
x
TRUNK
to access mode 3;
x
START
to access mode 4.
3. The parking lights will flash 1, 2, 3 or 4 times to confirm entry into a mode.
4. Release the brake pedal.
Once the desired mode has been selected, the unit will fall (by default) into function #1 of that mode; you can
now select the option you want in function 1. Once this option has been chosen, the unit will move on to
function 2 of the mode selected, and so on.
x
LOCK
to access option 1;
x
UNLOCK
to access option 2;
x
TRUNK
to access option 3;
x
START
to access option 4.
5. After the programming of any mode is completed, the parking lights and the LED on the antenna will turn
ON for 20 sec. During those 20 seconds, select one of the sub-menus if needed.
Entering programming mode using the
Hood Pin (or the P.B.)
Entering programming mode using the
A.P.B.
x
Press and hold the hood pin down for 4 seconds.
x
Make sure the hood is closed.
x
Release the hood pin.
The parking lights will turn
ON
for 1 second.
x
Turn the ignition key to the
IGNITION ON (RUN)
position.
x
While the parking lights are
ON
, press the hood pin
once more and release immediately.
The parking lights will come
ON
solid for
20 seconds.
x
You now have 20 sec. to select a submenu.
x
Within 5 seconds, press the programming button
on the antenna twice for 1 second each time.
The LED will come
ON
solid for 20 seconds.
x
You now have 20 sec. to select a submenu.
Note 1:
To exit programming mode, close the hood.
Note 1:
To exit programming mode, press on the
antenna button once (the LED will come
ON
) and
release.
Note 2:
For vehicles that require the ignition to be turned
ON
to activate the brake circuit, follow these steps to
select a submenu:
x
After flashing the hood pin, turn the ignition
ON
and wait for the parking lights to come
ON
(4 seconds).
Then, press the brake pedal to access the sub-menus.
