Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 73

Страница: 73 / 147

ENGINE OIL / FILTER CHANGE

Always check and change the engine oil at the intervals outlined in the Periodic
Maintenance Chart. Always change the oil filter whenever changing oil.

1. Position the vehicle on a level surface. Place the transmission in neutral.

Engage the park brake.

NOTE

The engine must be at normal operating temperature when checking or

changing the oil. Do not check or change the oil when the engine is cold.

2. Start the engine and allow it to idle for 2-3 minutes. Stop the engine.

CAUTION

Hot oil can cause burns to skin. Do not allow hot oil to contact skin.

3. Clean the area around the drain plug at the bottom of the crankcase.

4. Place a drain pan under the drain plug. Remove the drain plug. Allow the oil

to drain completely.

5. Clean the sealing surfaces of the drain plug and oil pan. The sealing surfaces

should be clean and free of burrs, nicks or scratches.

6. Reinstall the drain plug. DO NOT overtighten.

TORQUE

18 ft-lbs (25 Nm)

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды