Polaris EPC12-A1 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 25

background image

DC Inverter Monoblock Duct Type Air Conditioner Installation and Operation Manual

3

1 Unit Function

1.1 Setting of Double Indoor Room Sensors

This series of ducted air-conditioning unit has two indoor room sensors. One is located at the air
intake of the indoor unit and the other one is located inside the wire controller.
User can select one from the two indoor room sensors on the basis of the engineering
requirement.

(Refer to the section of wire controller instructions for detailed operation.)

Fig.1

Indoor Room Sensor A

Indoor Room Sensor B

«
...
4
5
6
7
8
...
»

Содержание EPC12-A1


























Отзывы:

Нет отзывов

Похожие инструкции для EPC12-A1

Бренд: b-mola Страницы: 16

Бренд: Quasar Страницы: 24

Бренд: Quasar Страницы: 24

Бренд: Quasar Страницы: 20

Бренд: York Страницы: 32

Бренд: Rasonic Страницы: 2

Бренд: Toyotomi Страницы: 38

Бренд: Midea Страницы: 104

LM012CI-115P432-1X

Бренд: Lennox Страницы: 44

Бренд: Saneo Страницы: 49

Бренд: Valeo Страницы: 60

Бренд: Olimpia splendid Страницы: 52

Бренд: Trotec Страницы: 16

Бренд: Scent Crusher Страницы: 12

Бренд: Carrier Страницы: 32

NTC5/GNJ Series

Бренд: ICP Страницы: 16

Бренд: Parker Страницы: 148

Бренд: Kampmann Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды