Polaris 700 Fusion Скачать руководство пользователя страница 43

Страница: 43 / 139

THE PERFECT FIT

IQ Front Suspension Adjustments

WARNING

Always verify ski alignment before making adjustments to the

IFS. See page 110 to check alignment. If the skis are misaligned,

see your dealer, as the camber adjustment may also be affected.

The tension at which the shock coil spring is set is called spring

preload. For the best ride, the spring preload should be set as low as

possible to use the full travel of the ski shock, with occasional light

bottoming. To determine if your machine is using full travel of the ski

shock, push the jounce bumper down as far as it will go on the shock

rod and test ride the machine. The bumper will move up on the rod in

direct relation to the amount of travel. If the shock travel is full, the

bumper will be seated at the top of the shock.

Shock Absorber Components

1. Retainer

2. Jounce Bumper (RydeFX only)

3. Shock Rod

4. Body

5. Threaded Spring Preload Adjuster Nut

Содержание 700 Fusion












































































































































Результаты поиска

Содержание 700 Fusion

Отзывы:

Похожие инструкции для 700 Fusion

Бренды по названию

Популярные бренды

Polaris 700 Fusion, Руководство пользователя

Результаты поиска

Содержание 700 Fusion

Отзывы:

Похожие инструкции для 700 Fusion

Бренды по названию

Популярные бренды