background image

70

MAINTENANCE

Engine Oil

Oil and Filter Change

9. Place shop towels beneath the oil filter. Using an oil filter wrench,

turn the filter (1) counterclockwise and remove.

10. Lubricate the gasket on the new filter with a film of new engine

oil. Check to make sure the gasket is in good condition. Also

make sure the gasket from the old filter is not still on the engine.

11. Install the new filter and tighten by hand 1/2 to 3/4 turn after

gasket contacts the engine.

12. Approximately one cup of

engine oil will remain in the

crankcase. To drain, remove

the drain plug on the lower

right side of the crankcase.

NOTE:

The sealing surfaces on

the drain plug and

crankcase should be

clean and free of burrs,

nicks or scratches.

13. Reinstall the drain plug and

torque to 14 ft. lbs. (19 Nm).

14. Remove the dipstick (2) and add two quarts (1.9 l) of the

recommended oil. Reinstall the dipstick.

NOTE:

If the sump is not drained, add about 1 3/4 quarts initially.

15. Place the gear selector in neutral and set the parking brake.
16.

Prime the oil pump using the procedure on page 71.

Then stop

the engine and inspect for leaks.

17. Recheck the oil level on the dipstick and add oil as necessary to

bring it to the recommended level on the dipstick.

18. Dispose of used filter and oil properly.

2

1

Содержание 2008 Scrambler 500 4X4


































































































































Отзывы: