Polar Spas AquaKing Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 23

background image

Apply silicone under the control panel before it is attached to the edge. It is enough to push
it down into the hole and it will be securely fastened when the silicone has dried.

Apply silicone around the
hole before you insert the
plastic plug. After the
silicone has dried excess
material can be pulled off.
Then make a protective
seal between tub and rim
using silicone.

Remove the top layer of masking tape
quickly.

Repeat the procedure for every joiint, when
the mass has dried apply TubCoat over the
joints and remove the remaining masking
tape.

5

6

«
...
20
21
22
23
»

Содержание AquaKing
























Отзывы:

Нет отзывов

Похожие инструкции для AquaKing

Бренд: Jacuzzi Страницы: 19

Spa MAXI Andros

Бренд: Jacuzzi Страницы: 40

SwimFun Swimspa

Бренд: SwimLife Страницы: 24

Бренд: Tubmarine Страницы: 12

Бренд: Aquatic Страницы: 1

Бренд: Aquatic Страницы: 1

HOTSOAK 72 AI12AIR7240HS

Бренд: Aquatic Страницы: 1

HOTSOAK 74 AI19AIR6636HS

Бренд: Aquatic Страницы: 1

HOTSOAK 70 AI8AIR6643HS

Бренд: Aquatic Страницы: 1

Hotsoak 65 AI6AIR6060HS

Бренд: Aquatic Страницы: 1

Бренд: Dermalife Страницы: 84

Бренд: HydroAir Страницы: 8

Бренд: Jacuzzi Страницы: 64

Бренд: Jacuzzi Страницы: 50

Бренд: UltraLift Страницы: 8

Бренд: Jacuzzi Страницы: 24

CADET 2775.XXXW Series

Бренд: American Standard Страницы: 4

Бренд: Solana Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды