Polar Air SWC-04-ECM Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 55

Polar Air SWC-04-ECM Скачать руководство пользователя страница 16

Page 14 of 52

PG2021_SWC-V-ECM_02

Safety Precautions

•

When installing, performing maintenance or servicing Polar Air fan coil units observe the precautions stated in this
manual as well as those stated on the labels attached to the unit.

•

Ensure all local and national safety codes, laws, regulations, as well as general electrical and mechanical safety
guidelines are followed for installation, maintenance and service.

•

The appliance is for indoor use only.

•

Ensure the correct power supply is provided.

•

If the power supply cord is damaged, it must be replaced by qualified personnel.

•

Installing and servicing fan coil unit should be performed by qualified service personnel only.

•

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or persons lacking in experience and knowledge of the appliance, unless they have been given supervision
or instruction concerning it.

•

User of this appliance is responsible for his/her own safety.

•

Warranty shall be voided if installation instructions and safety precaution stated in this manual are not observed.

•

Never cut off the mains supply when unit is under operation. The unit should only be switched off by using the ON-OFF
button on the control interface.

•

During connections, select pipe pliers according to pipe diameter to avoid damaging units over forced.

•

Untreated frozen water and cooling water may cause dirt accumulation and corrosion. Suggest using treated water.
Suggested working water pressure is below 1.6 Mpa.

•

When units are in cooling mode, suggested freezing water degree is

≥

7

℃

; When units are in heating mode, suggested

hot water degree is

≤

60

℃

.

•

Condensate water pipe, water connection pipe, water connectors and solenoid valve body must remain heat to avoid
condensation.

CAUTIONS

Before any service or maintenance operations turn off the mains electrical
supply.

DO NOT turn OFF the main power supply when the unit is operating. Turn off the
unit BEFORE turning off the main power

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

«
...
14
15
16
17
18
...
»

Содержание SWC-04-ECM
























































Отзывы:

Нет отзывов