Plymovent WALLPRO, Инструкция по установке и эксплуатации

Страница: 8 / 29

000115682/151018/0 WallPro EN - 7
WallPro “UL” types
11
(60Hz versions) only
- Components necessary for electrical installation according to
UL and federal, state or local wiring regulations
Option
In case of a dustbin extension set:
- duct Ø 200 mm or 8 in.
4.2 Unpacking
Make sure that the product is complete. The package contains:
Filter unit
- Filter unit (without side panels), incl. 10 m cable
12
- Wall bracket
- Dustbin set
- Air hose (filter pressure) 2x10 m
- SealApplicator (seal assembly lubricant)
- Filter disposal bag (5 pieces)
- Mounting material
Side panel (2)
- Side panel
Mounting kit
- Mounting and ducting material (types “DM” only)
- Inlet non-return valve
Additionally for “EM” configurations in 60Hz:
• Duct adapter metric-imperial
13
(WallPro Single: 1 piece | WallPro Double: 2 pieces)
For an overview of the mounting material per
specific configuration, refer to Fig. IV on page 22.
Extraction arm (1 or 2)
Refer to the installation manual of the KUA-160 or KUA-200,
that is supplied with the product.
Extraction fan
- Fan
- Fan outlet transition (from rectangular to round Ø 250 mm)
Control equipment
- Control box
4.3 Stationary filter unit
ATTENTION
It is important to follow the mounting sequence as
written in this (4.3) and the next (4.4) chapter.
The table below explains the various configuration types.
WallPro type Explanation
Single- 1 extraction arm
Double- 2 extraction arms
Basic no extraction arm(s)
160/ Arm diameter Ø 160 mm
200/ Arm diameter Ø 200 mm
3- Arm length 3 m
4- Arm length 4 m
DM Direct mount
EM External mount
11. The “UL” certification applies to the control box
12. For connection with the control box
13. From Ø 160 to Ø 6 in. / Ø 200 to Ø 8 in., depending on the configuration
CE Control box: CE marking
UL Control box: UL certified
A number of installation steps are only applicable to one or
more specific configurations. These are indicated at the
beginning of a certain paragraph. The grey/empty cells are
universal.
Some examples:
In case of:
Applies to all
“DM” types DM
In case of:
Applies to all
WallPro Single
types and all
“EM” types
WallPro Single-
EM
Write your configuration type below.
WallPro type

TIP
For stable assembly conditions, we recommend to
leave the filter unit on the pallet (until step 4.6).
4.3.1 Reinforcement plate
In case of:
DM
In case of a WallPro Single “DM” (direct mount) you must
install a reinforcement plate behind the lower part of the side
panel to carry the weight of the arm b extraction arm.
The package of the WallPro Double “DM” contains two
reinforcement plates for both sides of the filter housing.
In case of a WallPro type “EM” (external mount),
where the extraction arm is mounted separately
from the filter unit, the reinforcement plate is not
necessary. In that case, proceed with par. 4.3.2.
To install the reinforcement plate, do the following.
Fig. 4.2
• Insert the 4 cage nuts M12 from the inside in the
corresponding positions of the plate;
- KUA-160 / arm Ø 160 mm: inner positions (A)
- KUA-200 / arm Ø 200 mm: outer positions (B)
Fig. 4.2
A
B
Cage nuts