background image

Page 12 

Operating Instructions PCIe TS 

 

B3  Monitor Program 

The monitor program serves to monitor the “

Plura 

TimeSys” servi

ce and to adapt this service to 

the individual requirements. 

Starting the Program 

Run  the 

monitor  program  with  “Start  / 

All  Programs  /  Plura  /  Ti

meSys  Monitor”

.  It  requests 

Administrator rights and the monitor window opens: 

 

The following information will be shown:  

 

 

“System time”: 

The current system time of Windows. Time, difference to UTC in hours, date 

and difference to LTC in milliseconds are shown. The display refreshes every second. 

 

“LTC”: 

Readout LTC. Time, difference to UTC in hours, date and sync status (

“Sync” or “Not 

sync”)

. The display refreshes every second. 

Some information’s may

 be not shown if they 

are not provided by the LTC source. The display refreshes every second. 

 

“Last sync”: 

The point of time at which the LTC has last supplied the sta

tus “synchronous”

Time,  difference  to  UTC  in  hours  and  date  are  shown.  Depending  on  the  LTC  source,  it 

may  e.g.  be  seen  whether  a  connected  DCF  of  GPS  receiver  receives  a  valid  antenna 

signal. 

If  this  time  stands  still,  the  status  “synchronous”  has  not  be

en  detected  since  the 

shown time. This display refreshes about every 3rd second. 

 

“Last  set”: 

The  last  point  of  time  at  which  Windows  system  time  was  hard  set  last.  The 

following data are shown: Time, difference to UTC in hours, date and difference to LTC in 

milliseconds, which had been readjusted by this hard set. 

 

“Service status”: 

The status 

of the “

Plura 

TimeSys” service

“The s

e

rvice is running” indicates 

tha

t  the  “

Plura  TimeSy

s”  service  was  started  correctly  and  is  now  running  in  the 

background.  Other  messages  will  supply  indications  of  possible  errors  in  the 

communication between the monit

or program and the “

Plura 

TimeSys” ser

vice. 

Operation 

 

“Hard set” sets 

the Windows system time hard on the LTC. This may be useful if LTC and 

system  time  differ  quite  considerably,  so  the  system  time  needs  to  be  synchronized  once 

with the LTC. If the LTC source is providing date information, the system date will be set 

beside the time. 

Содержание PCI TS























Отзывы: