PLP B20 Скачать руководство пользователя страница 6

Страница: 6 / 28

Assembly

Assembling Engine and Drive Shaft Assembly

[Model BC26, BC30, L30, L45, BC45, BC50]

Attach the clutch drum housing to the engine using the four

screws supplied with the unit.

Loop Handle Installation

[Model B20]

Slip the rubber sleeve around the shaft.

[Model B20, B21, L20, L23, L26, L30, L45]

1. Place the loop handle and the bottom clamp on the shaft approximately

cm(

inches) from the end of the stop switch/throttle trigger assembly.

2. Install the four screws and nuts. Tighten the screws evenly.

3. Reposition the loop handle up or down the driveshaft to the

most comfortable position, and tighten the screw and nuts.

Horn Handle Installation

[Model BC26, BC30, BC45, BC50]

IMPORTANT: Be careful not to damage the throttle cable

and stop switch wires when you remove the horn handles

from the carton.

1. Loosen the four screws on the top of the clamp bracket.

2. Insert the left and right horn handles into the clamp bracket.

Note that the horn handle with the throttle trigger and stop

switch goes on the right-hand side of the Trimmer/ brushcutter.

3. Adjust the horn handles to the desired position, then tighten

the four screws.

[Model BC45, BC50]

4. Clamp the throttle cable assembly as shown.

Loop Handle

Screw (4)

Bottom Clamp

Nut (4)

[L20, L23, L26, L30, L45]

Loop Handle

Screw (4)

Bottom Clamp

Nut (4)

[B20]

Rubber sleeve

Throttle Trigger and Stop Switch

Stop Switch Wires
and Throttle Cable

Screw (4)

Horn Handle

Clamp Bracket

Engine

Screw (4)

Clutch Drum Housing

Loop Handle

Screw (4)

Bottom Clamp

Nut (4)

[B21]

[BC45, BC50]

[BC26, BC30, BC45, BC50]

Содержание B20





























Результаты поиска

Содержание B20

Отзывы:

Бренды по названию

Популярные бренды

PLP B20, Руководство оператора

Результаты поиска

Содержание B20

Отзывы:

Бренды по названию

Популярные бренды