manualshive.com logo in svg

PLP B20, Руководство оператора

Поделиться
Скачать
PLP B20 Скачать руководство пользователя страница 10

- 

9

 - 

 

[Except for model B20, B21]

 

     

IMPORTANT: Make sure the trimmer head is for 

 

     

LEFT-HAND ROTATION (counterclockwise) as viewed 

 

      from the operator’s position, and that the trimmer 

 

      head adapter is a male, M8 left-hand thread.

 

 

1. Remove the blade bolt and stabilizer from the attaching shaft   
    out of the gearcase. (keep the blade bolt and the stabilizer) 

    Note: The blade bolt has left-hand thread.

 

2. Align the hole in the boss adapter with the guide slot in the   

  gearcase. 
 
3. Insert the 

φ

3,5mm pin into the hole in the boss adapter and   

    the guide slot in the gearcase to lock the attaching shaft. 
 
 

4. Thread the trimmer head adapter into the attaching shaft, then   

    tighten the trimmer head by hand. 
 

    Note: The trimmer head adapter has left-hand thread.

 

 
5. Remove the 

φ

3,5mm pin from the boss adapter and gearcase. 

 

Brushcutter Blade [Except for model B20, B21] 

 

 

 

 

 

 

 

 

 

 

1. Remove the blade bolt, stabilizer and clamping washer   

  from the attaching shaft out of the gearcase.

     

  Note: The blade bolt has left-hand thread. 

 
2. Install the brushcutter blade onto the boss adapter, then   
    reinstall the clamping washer, stabilizer and blade bolt. 
 
3. Align the hole in the boss adapter with the guide slot in the   
  gearcase. 

 

 

 

 

 

 

 

 

 
 

Trimmer Head
Adapter

 

Attaching 
Shaft

 

Gearcase

Boss
Adapter

Holding Tool 
(

φ

3,5mm Pin) 

Washer

Trimmer Head

 

Left-hand 
thread

WARNING

 

 

POTENTIAL HAZARD 

 

・

If the Brushcutter blade is not adequately tightened, it can come loose from the Brushcutter   

   during use. 

 

WHAT CAN HAPPEN

 

 

・

This may cause damage to property or personal injury. 

 

HOW TO AVOID THE HAZARD

 

 

・

Make sure the Brushcutter blade is securely fastened to the attaching shaft in the gearcase. 

 

WARNING

 

 
 

POTENTIAL HAZARD 

 

・

Brushcutter blade is sharp. 

 
 

WHAT CAN HAPPEN

 

 

・

Contact with sharp blade can cause personal injury. 

 
 

HOW TO AVOID THE HAZARD

 

 

・

Wear gloves when you handle the blade. 

Brushcutter Blade

Washer

Stabilizer

Blade Bolt

Left-hand  
thread

Gearcase

Boss 
Adapter

Holding Tool 
(

φ

3,5mm Pin) 

Attaching
Shaft 

Содержание B20





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды