TC-N2000/TC-NT24H
DT Istr (TC-N2000/TC-NT24H) 05/13_Rev 6_05/2018
12/16
2.
This appliance must be connected to an approved mains socket that complies with the safety regulations on
electrical systems for civil purposes. The electrical system must be specific for the appliance rated voltage
and must be equipped with an earth cable.
3.
The appliance must be used only for its intended use, that is, as a heater for domestic heating. Any use
other than its intended purpose shall be deemed to be improper and hazardous.
4.
The manufacturer shall not be held responsible for damages derived from misuse of this appliance, do not
assuming any responsibility in case of incorrect use that will decline any warranty.
5.
Always place the fan heater on a flat and even surface, it should not be exposed to vibration or mechanical
stress.
6.
The appliance has dangerous components that must be kept out of the reach of children.
7.
Never connect the power cord to extensions or triple plugs. Do not pull or damage the power cord. Before
any maintenance operations, disconnect the plug from the mains socket.
8.
The power cord must never be in contact with the hot surfaces of the appliance.
9.
Do not lay the power cord under a carpet. Do not cover the power cord with a cover or similar elements.
Pay attention not to place the power cable where it is likely to get into people's way.
10.
If the appliance does not work properly, immediately turn it off and disconnect it from the mains socket.
For repairs, contact a technical support center authorized by the manufacturer, and require that original
spare parts be used. Using parts that do not conform to the product may seriously compromise its correct
operation.
11.
In order to unplug the appliance, select
"O"
and disconnect the plug from the power socket.
INSTRUCTIONS FOR USE
ASSEMBLING THE APPLIANCE
Before using the appliance, fix its feet (included separately in the box) to the
appliance. The feet must be fixed to the appliance base using the 4 self-threading
screws supplied, making sure they are correctly placed in their corresponding
positions on the bottom of the appliance.
SETTING THE APPLIANCE AT WORK
NOTE: When the appliance is set at work for the first time or after long periods of
inactivity, it could give a slight smell. This smell will disappear a little while
after turning it on.
TC-N2000 – Convector heater with thermostat and turbo fan mode
Position the appliance in the desired place, taking into account the safety
precautions included in this manual.
Connect the plug to the suitable mains socket.
Turn the thermostat knob clockwise until the maximum position.
Start the heating element by means of the starting lever located on the side
panel. When the heating element is on, the indicator lights up.
Once the desired temperature has been reached, the thermostat knob should be
set to a lower level by turning it anticlockwise slowly until the thermostat
tripping and the lights on the switches go off. After that, the appliance will keep the air in the room at the
selected temperature, automatically turning on and off. In the minimum level position (turning the knob fully
anticlockwise), the thermostat acts as an anti-freeze device. In such position (depending on the room
dimensions), the appliance will keep the temperature above the freeze threshold.
The TC-N2000 model is also equipped with an internal turbo fan, which can be turned on independently from
the heating element.
Setting the turbo fan at work: it is started by means of the corresponding button. The turbo fan will work with
the thermostat in position “On” and can be used when the heating element is started to blow hot air in the room.
When the room temperature is too high, the turbo fan can be used while the heating element is off, to blow cold
air in the room.
TC-NT24H – Convector heater with thermostat timer and turbo fan mode
All the instructions indicated above for the TC-N2000 model are also applicable for the TC-NT24H model.
In addition, this model also features a 24h timer with 96 segments around its circumference. Each segment is
equal to 15 minutes. Thanks to the timer, it is possible to programme the periods during which the appliance
should remain on in 24 hours.
