Playnation Cartecay 1701 Скачать руководство пользователя страница 57

Страница: 57 / 79

STEP 22: LADDER ASSEMBLY

1: LAY ONE 2 X 4 X 57" LADDER SIDE ON A FLAT SURFACE WITH THE CHANNELS FACING DOWN. PLACE THE BARREL

OF A T-NUT IN THE HOLE AT THE TOP OF THE LADDER SIDE AND SECURE WITH A HAMMER. REPEAT THIS STEP FOR

THE OTHER LADDER SIDE.

2: FLIP THE LADDER SIDE OVER SO THAT THE CHANELS ARE FACING UP.

3: PLACE THE LADDER STEPS INTO THE CHANNELS, AND THEN PLACE THE SECOND LADDER SIDE ON TOP, WITH THE

CHANNELS FACING DOWN.

4: NOW DRIVE TWO 2" WOOD SCREWS THROUGH THE LADDER SIDE INTO EACH STEP.

5: CAREFULLY TURN THE LADDER OVER AND FINISH THE OTHER SIDE WITH TWO 2" WOOD SCREWS PER STEP.

6: INSTALL TWO 90 GREEN BRACKETS USING 5/16" X 1-1/2" BOLTS AND 5/16" WASHERS.

7: INSTALL THE 5/4" X 4 X 18-1/2" LADDER BACK ABOVE THE OPENING OF THE TOP CHANNELS WITH ONE 2" WOOD

SCREW PER SIDE.

5/16" WASHER

LADDER STEP

2" WOOD SCREW

GREEN BRACKET

T-NUT

2 X 4 X 57"

2" WOOD SCREW

5/4" X 4 X 18-1/2"

LADDER SIDE RIGHT

2" WOOD SCREW

2 X 4 X 17"

LADDER BACK

5/16" X 1-1/2" HEX BOLT

2 X 4 X 57"

LADDER SIDE LEFT

Содержание Cartecay 1701
















































































Результаты поиска

Содержание Cartecay 1701

Отзывы:

Похожие инструкции для Cartecay 1701

Бренды по названию

Популярные бренды

Playnation Cartecay 1701, Сборка

Результаты поиска

Содержание Cartecay 1701

Отзывы:

Похожие инструкции для Cartecay 1701

Бренды по названию

Популярные бренды