background image

INSTALLATION AND OPERATING INSTRUCTIONS

Table of Contents

Warnings and Safe Play Instructions  .  .  .  .  .  .  .  .  .  . pg . 2
Protective Surfacing Guidelines .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 3
Instructions for Proper Maintenance   .  .  .  .  .  .  .  .  . pg . 4
About Our Wood – Limited Warranty  .  .  .  .  .  .  .  .  . pg . 5
Keys to Assembly Success   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 6
Part ID   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 9
Step-By-Step Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 20
Installation of I .D ./Warning Plaque  .  .  .  .  .  .Final Step

To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and 

refer to these instructions often and give them to any future owner of this play set. Manufacturer 

contact information provided below.

OBSTACLE FREE SAFETY ZONE - 32’ 11-3/4” x 27’ 9-1/2” (10.06 x 8.49 m) area requires Protective Surfacing. See page 3. 

MAXIMUM VERTICAL FALL HEIGHT - 7’ 8” (2.01 m)

CAPACITY - 15 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.

RESIDENTIAL HOME USE ONLY. Not intended for public areas such as multi-unit residences, schools, churches, nurseries, day cares or parks.

Warning. Only for domestic use.

WARNING

Rev 09/17/2019

9409080

Cedar Summit by KidKraft 

4630 Olin Road 

Dallas, TX 75244, United States 
customersupport@kidkraft .com

Online Parts Replacement:

Cedarsummitplay .com/parts-center-warranty-claim

Customer Service: 

1(800) 933-0771 or (972) 385-0100
KidKraft Netherlands BV

Olympisch Stadion 8

1076 DE Amsterdam, The Netherlands
Europe Customer Service: +31 (0)20 305 8620

europecustomerservice@kidkraft .com 

EU Online Parts Replacement: parts .kidkraft .eu

For Outdoor Family Domestic Use Only

14 - 18 Hrs

FOR FORT & SWING

TWO PERSON  

ASSEMBLY

2-4 Hrs

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON  

ASSEMBLY

10 - 12 Hrs

FOR FORT & SWING

1 - 2 Hrs

TUBE SLIDE

11’ 5-1/4” 

3.49 m 

27’ 9-1/2” 

8.49 m 

19’ 10-1/2” 

6.06 m 

32’ 11-3/4” 

10.06 m 

HILLTOP PLAYSET F29080

Содержание Cedar Summit F29080





















































































































Отзывы: