Playnation 2300 Скачать руководство пользователя страница 48

Страница: 48 / 131

THE THREE COUNTER-SUNK

HOLES ON THE SWING BEAM

SUPPORT WILL FACE DOWN

WHEN PROPERLY INSTALLED.

3/8" NUT

DETAIL A

SCALE 2 : 19

TORQUE WASHER

BOLT

3/8" WASHER

6-1/2"

CARRIAGE

BOLT CAP

FORT

HEX BOLT

FRONT

4 X 4 X 47-1/2"

SWING BEAM MOUNT

5/16 X 4-1/2"

5/16" WASHER

4 X 4 X 110"

CORNER POST

LEFT

2 X 6 X 47-1/2"

BOTTOM

PANEL BOARD

(OFFSET DOWN)

2 X 6 X 47-1/2"

SANDBOX BOARD

(OFFSET DOWN)

STEP 4: ASSEMBLING THE LEFT SIDE FRAME

1: LAY THE LEFT SIDE CORNER POSTS ON THE GROUND IN THEIR PROPER ORIENTATION.

2: LAY THE 2 X 6 X 47-1/2" SANDBOX BOARD ON TOP OF THE LEFT SIDE CORNER POSTS AT THE BOTTOM OF

THE CORNER POSTS. THE HOLES IN THE SANDBOX BOARD MUST BE OFFSET DOWN.

3: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD

TO THET-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

4: LAY THE 2 X 6 X 47-1/2" BOTTOM PANEL BOARD ON TOP OF THE LEFT SIDE CORNER POSTS IN THE MIDDLE

OF THE CORNER POSTS. THE HOLES IN THE BOTTOM PANEL BOARD MUST BE OFFSET DOWN.

5: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE BOTTOM HOLES OF THE BOTTOM PANEL

BOARD TO THE T-NUTS INSTALLED ON THE CORNER POSTS. THE TOP HOLES WILL BE USED LATER.

6: LAY THE 4 X 4 X 47-1/2" SWING BEAM MOUNT ON TOP OF THE LEFT SIDE CORNER POSTS. THE THREE

COUNTER-SUNK HOLES IN THE MIDDLE OF THE SWING BEAM SUPPORT MUST FACE DOWNWARD.

7: FIND TWO TORQUE WASHERS. PLACE A 6-1/2" CARRIAGE BOLT THROUGH THE TORQUE WASHER,

MAKING SURE THAT THE TEETH ARE FACING IN THE SAME DIRECTION AS THE THREADS OF THE CARRIAGE

BOLT. PLACE THE TORQUE WASHER/CARRIAGE BOLT ASSEMBLY INTO THE CORNER POST HOLES SO THAT THE

HEAD OF THE CARRIAGE BOLT FACES WHAT WILL BE THE INSIDE OF THE FORT. USE A HAMMER TO SET THE

TORQUE WASHER INTO THE CORNER POST.

8: ATTACH THE SWING BEAM SUPPORT AS SHOWN IN DETAIL A.

Содержание 2300




































































































































Результаты поиска

Содержание 2300

Отзывы:

Похожие инструкции для 2300

Бренды по названию

Популярные бренды

Playnation 2300, Руководство пользователя

Результаты поиска

Содержание 2300

Отзывы:

Похожие инструкции для 2300

Бренды по названию

Популярные бренды