Playnation 2300 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 131

background image

PLAYNATION WARRANTY

In addition, within the first 30 days from the date of purchase, PlayNation will replace any parts
discovered to be missing from or damaged in the original packaging.

This warranty is valid only if the product is used for the purpose for which it was designed and installed
at a residential, single-family dwelling. This warranty is void if the product is used in a commercial,
institutional or multi-family setting. This warranty does not cover normal wear and tear or (a) products
that have been damaged by acts of God and/or nature, negligence, misuse or accident; (b) products that
have been modified or repaired by unauthorized persons; (c) the cost of labor; or (d) the cost of shipping
any replacement product or part.

PLAYNATION DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESSED,
IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. PLAYNATION WILL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the
product subsequent to the original purchaser. Some states do not allow limitations on implied
warranties or exclusion of incidental or consequential damages, so these restrictions may not be
applicable to you. This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.

«
...
2
3
4
5
6
...
»

Содержание 2300




































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2300

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Egatronik 51249

Бренд: Ega Master Страницы: 22

Бренд: Conrad Страницы: 34

BELLS - OCTAVIA OPTION

Бренд: Creative Play Страницы: 5

Бренд: Color imagination Страницы: 12

Electronic Instrument for Music Education and Performance

Бренд: Quintet Страницы: 35

B-Control Deejay BCD3000

Бренд: Behringer Страницы: 13

Бренд: HABYS Страницы: 20

Бренд: Ibiza Страницы: 32

PLAYZONE AQ2711

Бренд: airquee Страницы: 3

traktor kontrol s5

Бренд: Native Instruments Страницы: 211

Бренд: ELAN Lighting Страницы: 10

Бренд: Lanex Страницы: 12

LED Quadbar 1 DMX

Бренд: KAM Страницы: 4

Бренд: Kellfri Страницы: 16

Batt-O-Meter KS700-0658

Бренд: Keith McMillen Instruments Страницы: 4

Бренд: Keysight Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды