Playnation 1500CWF Скачать руководство пользователя

Страница: 50 / 163

STEP 6B: ANGLE SUPPORTS

1: FOUR 2 X 4 X 18" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE LEFT AND

RIGHT SIDES OF THE PLAY SET TO THE 2 X 6 BOTTOM PANEL BOARD. THE TOP OF THE

ANGLE SUPPORT SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

2: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE ANGLE SUPPORT INTO THE

BOTTOM PANEL BOARD. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO

FASTEN THE ANGLE SUPPORT TO THE CORNER POST.

3: FOUR 2 X 4 X 13" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE FRONT

AND REAR OF THE PLAY SET TO THE 2 X 4 DECK SUPPORTS. THE TOP OF THE ANGLE

SUPPORT SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

4: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE DECK SUPPORT INTO THE ANGLE

SUPPORT. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE

SUPPORT TO THE CORNER POST.

SCREW

2" WOOD

SUPPORT

SCREW

2" WOOD

SCREW

2-1/2"

WOOD

BOTTOM

PANEL

BOARD

2 X 4 X 18"

ANGLE

SUPPORT

3" WOOD

SCREW

3" WOOD

SCREW

2 X 6

2 X 4 X 13"

DECK

SUPPORT

BOTTOM

BOARD

PANEL

DETAIL A

ANGLE

2 X 4 X 13"

SCALE 1 : 9

SUPPORT

DECK SUPPORT

SHOULD BE FLUSH OR LOWER

THAN THE DECK SUPPORT

TOP OF ANGLE SUPPORTS

2 X 6

2 X 4 X 18"

ANGLE

SUPPORT

Содержание 1500CWF




































































































































































Результаты поиска

Содержание 1500CWF

Отзывы:

Похожие инструкции для 1500CWF

Бренды по названию

Популярные бренды

Playnation 1500CWF, Инструкция по сборке

Результаты поиска

Содержание 1500CWF

Отзывы:

Похожие инструкции для 1500CWF

Бренды по названию

Популярные бренды