manualshive.com logo in svg

Playnation 1500CWF, Инструкция по сборке

Поделиться
Скачать
Playnation 1500CWF Скачать руководство пользователя страница 109

STEP 3: ATTACHING THE LADDER TO THE 

MONKEY BAR ASSEMBLY

1:  LOCATE TWO 8-5/8" W X 6-1/2"H MONKEY BAR PLATES, EIGHT 5/16" X 3-1/2"L HEX BOLTS AND 

EIGHT 5/16" FLAT WASHERS.  

LOOSELY

 ATTACH THE LADDER ASSEMBLY TO THE MONKEY BAR 

ASSEMBLY WITH THE MONKEY BAR PLATES.  USE 5/16" X 3-1/2"L HEX BOLTS WITH 5/16" FLAT 

WASHERS TO ATTACH THE MONKEY BAR PLATES TO THE TEE NUTS PREVIOUSLY INSTALLED.
2:  ONCE ALL THE HEX BOLTS ARE STARTED IN THE TEE NUTS TIGHTEN THEM DOWN.  
NOTE:  THE SELF TAPPING SCREWS INSTALLED IN STEPS 1 & 2 SHOULD BE FACING BACK SIDE OF 

THE LADDER ASSEMBLY AND THE UNDER SIDE OF THE MONKEY BAR ASSEMBLY.

LADDER.

STEP 2 SHOULD BE ON THE UNDER SIDE OF THE 

PLATE TO THIS 

SIDE

NOTE: SELF TAPPING SCREWS INSTALLED IN 

MONKEY BAR 

MONKEY BAR PLATE

ATTACH OTHER 

MONKEY BAR ASSEMBLY FROM STEP 2

5/16" FLAT WASHER

5/16" X 3-1/2" HEX HEAD BOLT

MONKEY BAR ASSEMBLY.

LADDER ASSEMBLY FROM STEP 1

STEP 1 SHOULD BE ON THE BACK SIDE OF THE 

NOTE: SELF TAPPING SCREWS INSTALLED IN 

COUNTERSUNK

HOLES ON TOP.

Содержание 1500CWF




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды