PlayNation Play Systems 1500DT Скачать руководство пользователя страница 56

Страница: 56 / 145

5/16" WASHER

5/16" X 3-1/2"

LAG SCREW

***IMPORTANT***

INSTALL LAG SCREWS AND WASHERS

ONLY IN THESE FOUR 2 X 6 BOARDS FIRST.

THEN LEVEL/SQUARE THE FRAME. FINALLY,

INSTALL LAG SCREWS IN THE REMAINING

2 X 6 BOARDS.

STEP 6A: LEVELING THE PLAY SET AND LAGS

1: INSTALL LAG SCREWS ONLY IN THE FOUR 2 X 6 BOARDS AT DECK HEIGHT AT THIS TIME.

THIS IS TO MAKE THE STRUCTURE RIDGID FOR THE LEVELING AND SQUARING PROCESS.
2: PLACE THE FRAME IN ITS FINAL POSITION AND FOLLOW THE PROCEDURES AT THE FRONT

OF THE MANUAL TO LEVEL AND SQUARE THE STRUCTURE. HAVE AN ASSISTANT HELP YOU

LIFT THE FRAME AS REQUIRED.

DO NOT

INSTALL REMAINING LAG SCREWS UNTIL AFTER THE

FRAME HAS BEEN LEVELED AND SQUARED.
3: ONCE THE FRAME IS LEVEL, SQUARE AND SET INTO POSITION; GO BACK AND INSERT

THE 5/16" X 3-1/2" LAG SCREWS AND 5/16" WASHERS IN ALL OF THE REMAINING HOLES OF

THE 2 X 6 PARTS ON THE FRONT, SIDES AND REAR OF THE PLAY SET. NOTE: THERE WILL NOT

BE ANY PREDRILLED HOLES IN THE CORNER POSTS FOR THE LAG SCREWS.

Содержание 1500DT


















































































































































Результаты поиска

Содержание 1500DT

Отзывы:

Похожие инструкции для 1500DT

Бренды по названию

Популярные бренды

PlayNation Play Systems 1500DT, Руководство пользователя

Результаты поиска

Содержание 1500DT

Отзывы:

Похожие инструкции для 1500DT

Бренды по названию

Популярные бренды