VDSL2 Converter
User’s Manual
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
Mark Warning
plies with the requirements relating to el
ement of
nd it may be possible
and trademarks are the properties of their respective companies.
in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including interference that
may cause undesired operation.
CE
This equipment com
ectromagnetic
compatibility, EN 55022 Class A for ITE, the essential protection requir
Council Directive 89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products a
that information in this document is not up-to-date. Please check with your local
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names
Copyright © 2007, All Rights Reserved.
Unpacking Information
Thank you for purchasing the Ethernet over VDSL2
converter. Before installation, please check that your
package contains the following items.
1.
One Ethernet over VDSL2 converter
2.
One power adapter
3.
One telephone line
4.
One user’s manual
Introduction
General Description
The VDSL2 supports the signal conversion between
upports symmetry and
pecifications of the connection are listed as
, Category 3, 4 or 5 UTP/STP
elephone wires
traditional Ethernet and innovative VDSL2 technology.
The device is a right solution to integrate current
Ethernet application with the new building phone line
networking technology, like hotel, office and
apartment environment.
The EoVDSL2 port s
asymmetry data transmission bandwidth up to
50Mbps and transmission distance up to 1000ft. It is
ideal for providing video-on-demand and multi-media
service to apartment, hotel and campus without
rewiring cable consideration. Moreover, the distance
expansion also provides wide range coverage.
The converter is plug-n-play without any software to
configure and also fully compliant with all kinds of
network protocols. Moreover, the rich diagnostic LEDs
on the front-panel provide the operating status of the
system.
The cable s
following:
10BASE-T
100BASE-TX, Category 5 UTP/STP
Ethernet over VDSL2, Twisted-pair t
The drawing listed below is typical application for the
Ethernet over VDSL2 converter.
Telephone
Slave
Master
Phone line
Key Features
E802.3 10BASE-T standard.
rd.
y
he Rear Panel
Dip Switch Settings
Pin3 Pin4
y
Complies with IEE
y
Complies with IEEE802.3u 100BASE-TX standa
y
Compliance with VDSL2 ITU-T G.993.2
y
Supports 1 * RJ-11 port for Ethernet over VDSL2.
y
Provides 1 * RJ-11 port for telephone connection.
y
Provides 2 * RJ-45 ports for 10/100Mbps Ethernet.
y
Provides 1 * Dip Switch for mode selection
line
y
Voice and Data work on the same telephone
y
EoVDSL2 port supports maximum
stream
bandwidth 100Mbps/50Mbps (down
/upstream) over 1000ft (300m)
Long Reach VDSL2 performance around 7Mbps
downstream over 5000ft (1500m)
y
Mini size design (120 x 75 x 25mm)
y
Provides rich diagnostic LED indicators
y
External Power Adapter
The Front Panel
T
Pin1 Pin2
Side Mode
R
t
ate
limi
SNR
ON Sla
E
)
ve (
CP
Fast No
limit 6dB
OFF Master (
CO
) Interleave 5
0/20 Mbps
9dB
Pin1: Master, slave switch
Master
(CO): EoVDSL2 converter acts as
Master
/
Central Office (CO) side.
Slave
(CPE): EoVDSL2 converter acts as
Slave
/
Customer Premise Equipment (CPE) side.
Pin2: Impulse noise protection
Fast mode: Direct data transmission with latency less
than 1 ms.
Interleave mode: Provides communication protection
for up to 250ms impulse noise with latency less than 6
ms.
Pin3: Rate limit control
No limit: Provides up to 100Mbps/50Mbps line rate in
s
short line.
50/20 Mbp : Line rate limited to 50/20Mbps.
Pin4: General protection
6dB: Original channel noise protection with 6 dB SNR.
9dB: Better channel noise protection with SNR up to 9
dB.
Note: SNR (Signal Noise Rate) = Signal / Noise. Switch on this
pin depends on your network demand.
