background image

i

Trademarks

Copyright 

 PLANET Technology Corp.

Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.

FCC Warning

This equipment has been tested and found to comply with the limits for
a Class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.

This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instruction manual
may cause harmful interference to radio communications. Its operation
in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference as his own expense.

Changes or modifications not expressly approved by the parties
responsible for compliance could void the user's authority to operate the
equipment.

CE Marking Warning

This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Revision:

User's Manual for PLANET PC Card family,
Model: 

ENW-3502-T

Ethernet PC Card with TP jack only

Part No.: EM3502T

Rev: 1.0 (May, 1998)

About This Manual

This is a user's guide for your ENW-3502-T PCMCIA 10Mbps Ethernet
Card. Please read this manual before you attempt to install the product.
This manual includes the following topics:

Ø

 

Product descriptions, features and specifications.

Ø

 

Hardware installation procedures

Ø

 

Software installation procedures

Содержание ENW-3502-T


































Отзывы: