manualshive.com logo in svg

Planet ADE-4110, Руководство пользователя, Страница: 38 / 67

Поделиться
Скачать
Planet ADE-4110 Скачать руководство пользователя страница 38

 

32

 

 

NAT:

 Use this field to Enable/Disable NAT. Default is Enable. 

 

Mode:

 Options for the NAT dropdown menu are: 

 

l 

NAT:

 Static peer-to-peer mode (1x1). 

l 

NAPT:

 Static multiple mapping mode (1xN). 

l 

Dynamic NAPT (default):

 Dynamic multiple mapping mode (NxN). 

 

Session Name:

 It allows you to select the session from the configured NAT Session 

Name Configuration. 
 

User

’

s IP:

 It allows you to assign the IP address to map the corresponding NAT/NAPT 

sessions. 
 

Session Name Status:

 This table will be displayed at the middle of the page to show the 

Session Name with its corresponding IP Address. 
 

Number of NAT Configurations:

 It displays the total number of NAT Sessions entered. 

 

Available Sessions:

 This table will be displayed at the bottom of the page to show all the 

available Session Names with their corresponding WAN Interface. 
 

Number of Sessions:

 It displays the total number of NAT Sessions entered. 

Содержание ADE-4110




































































Отзывы:

Нет отзывов