Planet Networking & Communication WRT-414 Скачать руководство пользователя страница 83

Страница: 83 / 93

Parameters

Description

Configuration Tools

Use the "

Backup

" tool to save WRT-414 current configuration to a file

named " config.cfg " in your PC. You can then use the "

Restore

" tool to

restore the saved configuration to WRT-414. The "

Restore to Factory

Defaults

" tool can force WRT-414 to perform a power reset for restore it to

original factory settings.

After configuration complete, please click “Apply”

button to save the configuration. Then you will see a

screen to prompt you the settings are save successfully. You may press “Continue” for configure other

settings or “Apply” to restart WRT-414 with new configuration.

8.2 Firmware

Upgrade

- 77 -

This page prompt you it allows you to upgrade the router’s firmware. Please press “Next” to

continue.

Содержание WRT-414






























































































Результаты поиска

Содержание WRT-414

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication WRT-414, Руководство пользователя

Результаты поиска

Содержание WRT-414

Отзывы:

Бренды по названию

Популярные бренды