Planet Networking & Communication WRT-414 страница 69 Скачать руководство пользователя

Страница: 69 / 93

Parameter

Description

Mode

Shows the current operation mode. You may set WRT-414 to other

operating mode by select other operating mode.

Band

2.4GHz (B):

It forces the WRT-414 to operate in 802.11b only.

2.4GHz (G):

It forces the WRT-414 to operate in 802.11g only.

2.4GHz (B+G):

It allows the WRT-414 to operate in 802.11b and 802.11g

simultaneously.

ESSID

Please make sure the ESSID of the wireless network that you will

connected and enter the correct ESSID in this field. The default value is

“

default

”.

WLAN MAC

Keep default setting

: WRT-414 will use it’s own MAC address to access

the wireless LAN.

Press “MAC Clone” button

: It will use PC’s MAC address to access the

wireless LAN.

After configuration complete, please click “Apply”

button to save the configuration. Then you will

see a screen to prompt you the settings are save successfully. You may press “Continue” for

configure other settings or “Apply” to restart WRT-414 with new configuration.

6.4

AP Bridge - Point to Point Mode

- 63 -

This function allows WRT-414 to bridge 2 wired Ethernet networks wirelessly.

Содержание WRT-414






























































































Результаты поиска

Содержание WRT-414

Отзывы:

Похожие инструкции для WRT-414

Бренды по названию

Популярные бренды

Planet Networking & Communication WRT-414, Руководство пользователя

Результаты поиска

Содержание WRT-414

Отзывы:

Похожие инструкции для WRT-414

Бренды по названию

Популярные бренды