Planet Networking & Communication WNRT-617 Скачать руководство пользователя страница 65

Страница: 65 / 155

User’s Manual of WNRT-617

-58-

setting and is recommended.

DTIM Interval

This value determines the interval of the Delivery Traffic Indication

Message (DTIM). A DTIM field is a countdown field informing clients of

the next window for listening to broadcast and multicast messages.

When the Router has buffered broadcast or multicast messages for

associated clients, it sends the next DTIM with a DTIM Interval value.

You can specify the value between 1-255 Beacon Intervals. The

default value is 1, which indicates the DTIM Interval is the same as

Beacon Interval.

Enable WMM

WMM

function can guarantee the packets with high- priority messages

being transmitted preferentially. It is strongly recommended enabled.

Enable Short GI

This function is recommended for it will increase the data capacity by

reducing the guard interval time.

Enabled AP Isolation

This function can isolate wireless stations on your network from each

other. Wireless devices will be able to communicate with the Router

but not with each other. To use this function, check this box. AP

Isolation is disabled by default.

Table 5-19

If you are not familiar with the setting items in this page, it's strongly recommended to keep

the provided default values; otherwise it may result in lower wireless network performance.

Содержание WNRT-617




























































































































































Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication WNRT-617, Руководство пользователя

Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды