Planet Networking & Communication WNRT-617 Скачать руководство пользователя страница 16

Страница: 16 / 155

User’s Manual of WNRT-617

-9-

Chapter 3. Connecting the Router

3.1 System Requirements

Broadband Internet Access Service (DSL/Cable/Ethernet connection)

One DSL/Cable Modem that has an RJ-45 connector (not necessary if the Router is

connected directly to the Ethernet.)

PCs with a working Ethernet Adapter and an Ethernet cable with RJ-45 connectors

PC of subscribers running Windows 98/ME, NT4.0, 2000/XP, Windows Vista / Win 7, MAC

OS 9 or later, Linux, UNIX or other platform compatible with

TCP/IP

protocols

Above PC installed with WEB Browser

It is recommended to use Internet Explore 7.0 or above to access the Router.

3.2 Installing the Router

Before installing the Router, make sure your PC is connected to the Internet through the broadband

service successfully at this moment. If there is any problem, please contact your local ISP. After that,

please install the Router according to the following steps. Don't forget to pull out the power plug and

keep your hands dry.

Step 1.

Power off your PC, Cable/DSL Modem, and the Router.

Step 2.

Locate an optimum location for the Router. The best place is usually at the center of your

wireless network.

Step 3.

Adjust the direction of the antenna. Normally, upright is a good direction.

Содержание WNRT-617




























































































































































Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication WNRT-617, Руководство пользователя

Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды