Planet Networking & Communication WDAP-C7200E Скачать руководство пользователя

Страница: 16 / 85

User Manual of WDAP-C7200E

-9-

Wireless MAC address filtering

User Isolation

Max. SSIDs

Max. Clients

64 per radio (50 is suggested, depending on usage)

Max. WDS Peers

Wireless QoS

Supports Wi-Fi Multimedia (WMM)

Wireless Advanced

WMM (Wi-Fi Multimedia): 802.11e Wireless QoS

Multiple SSID: up to 4 at 2.4GHz and 5GHz, respectively

Wireless Isolation: Enables to isolate each connected wireless client from

communicating with each other

Provides Wireless Statistics

Wireless Advanced

Auto Channel Selection

5-level Transmit Power Control (100%, 75%, 50%, 25%, 12.5%)

Client Limit Control, Coverage Threshold

Wi-Fi channel analysis chart

Status Monitoring

Device status, Wireless client List

PLANET Smart Discovery

DHCP client table

System Log supports remote syslog server

VLAN

IEEE 802.1Q VLAN (VID: 3~4094)

SSID-to-VLAN mapping up to 4 SSIDs

Self-healing

Supports auto reboot settings per day/hour

Management

Remote management through PLANET DDNS/ Easy DDNS

Configuration backup and restore

Supports UPnP

Supports IGMP Proxy

Supports PPTP/L2TP/IPSec VPN Pass-through

SNMP v1/v2c/v3 support, MIB I/II, Private MIB

Central Management

[1]

Applicable controllers: WAPC-500, WAPC-1000 and Smart AP Control(SAPC)

Remarks

[1]: The feature will be supported through firmware/system upgrade.

Environment & Certification

Temperature

Operating: 0 ~ 40 degrees C

Storage: -40 ~ 70 degrees C

Humidity

Operating: 10 ~ 90% (non-condensing)

Storage: 5 ~ 90% (non-condensing)

Regulatory

CE, RoHS

Содержание WDAP-C7200E






















































































Результаты поиска

Содержание WDAP-C7200E

Отзывы:

Похожие инструкции для WDAP-C7200E

Бренды по названию

Популярные бренды

Planet Networking & Communication WDAP-C7200E, Руководство пользователя

Результаты поиска

Содержание WDAP-C7200E

Отзывы:

Похожие инструкции для WDAP-C7200E

Бренды по названию

Популярные бренды