Planet Networking & Communication VGW-800FO Скачать руководство пользователя страница 39

Страница: 39 / 76

8-Port SIP Internet Telephony Gateway

VGW-800 Series

Chapter 5 VoIP Setting

5.1 SIP

Item

Explanation

Session Timer

Enable session timer or not (RFC 4028)

Session Expiry

(sec)

This is the setting of initial session timer expires time according to
RFC4028 - Session Timers in the Session Initiation Protocol

Min SE

The minimum session timer allowed when receiving a call with
session timer value according to RFC 4028

Session Timer

Refresh Method

The session timer refresh method

PRACK

Enable provision ACK or not (RFC 3262)

None: Disable PRACK

Supported: When selecting this mode, 100rel will be added

to the support list. It indicates the VGW-800 series can
support the PRACK but not mandatory.

Require: PRACK is mandatory required.

SIP Local Port

The SIP local service port (default is 8080)

SIP QoS Type

Quality of Service Type for SIP signaling

None: Not using QOS Tag and

not enables QOS.

DiffServ: Differentiated Services Value. Input DSCP value

0-63 for DSCP

TOS: Type of Service which include IP precedence value

and TOS.

Accept Proxy Only

Only accept the call coming from the SIP proxy. Does not accept
peer to peer call in this mode

P2P Call Alive

Detection

Check whether info communication exists; if not, FXO will
automatically terminate the link.
This function is only for P2P on FXS and FXO.

Содержание VGW-800FO













































































Результаты поиска

Содержание VGW-800FO

Отзывы:

Похожие инструкции для VGW-800FO

Бренды по названию

Популярные бренды

Planet Networking & Communication VGW-800FO, Руководство пользователя

Результаты поиска

Содержание VGW-800FO

Отзывы:

Похожие инструкции для VGW-800FO

Бренды по названию

Популярные бренды