Planet Networking & Communication VGW-800FO Скачать руководство пользователя страница 14

Страница: 14 / 76

8-Port SIP Internet Telephony Gateway

VGW-800 Series

URL / IP / MAC / Port Filter

Application Program Filter

Port Forwarding (TCP, UDP or both)

Bandwidth control (download and upload), maximum bandwidth

priority setting

UPnP Server at LAN port

Behind NAT, use DMZ for NAT traversal

SNTP with time zone and Daylight Saving

TCP/UDP (RFC 793/768), RTP/RTCP (RFC 1889/1890), IPV4 ICMP (RFC

792)

VoIP VLAN Support 802.1Q, 802.1P

VLAN ID Range: 2 to 4094

VLAN Priority: 0 to 7 (Highest Priority)

QoS: DiffServ (RFC 2475), TOS (RFC791, 1394)

Voice Gateway

RFC3261 compliance

Supports up to 24 SIP Trunks to Register

SIP UDP Protocol

Supports SIP compact Form

Supports SIP HOLD Type: Send Only, 0.0.0.0 or inactive

SIP Session Timer (RFC 4028)

SIP Session Refresher: UAC or UAS

SIP Encryption

MD5 Digest Authentication (RFC2069/RFC2617)

Reliability of provision response PRACK (RFC3262)

Early/Delay Media support

Offer/Answer (RFC3264)

Message Waiting Indication (RFC3842)

Event Notification (RFC3265)

REFER (RFC3515)

Supports Outbound Proxy

Supports Primary and Backup SIP Server

Supports STUN NAT Traversal

Supports “rport” parameter (RFC 3581)

Configure SIP local Port

SIP QoS Type: DiffServ or QoS

Accept Proxy Only : Yes or No

Содержание VGW-800FO













































































Результаты поиска

Содержание VGW-800FO

Отзывы:

Похожие инструкции для VGW-800FO

Бренды по названию

Популярные бренды

Planet Networking & Communication VGW-800FO, Руководство пользователя

Результаты поиска

Содержание VGW-800FO

Отзывы:

Похожие инструкции для VGW-800FO

Бренды по названию

Популярные бренды