Planet Networking & Communication ICS-2100T Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 76

Planet Networking & Communication ICS-2100T Скачать руководство пользователя страница 47

User’s Manual of ICS-2x00T Serial Device Server Series

47

4.5.2 Operation mode

The industrial serial server makes connected Serial equipment become IP-based. That also makes them able to connect to a
TCP/IP networking immediately. The industrial serial server allows traditional Computer/Client COM ports access to a serial
equipment anywhere on the Ethernet LAN network.

This operation mode can be set up as

Disable

,

Remote Pair Master/Slave

,

RF2217

,

Serial Telnet

,

TCP Server

,

TCP Client

,

UDP

,

Virtual COM

and

Modbus Converter Server/Client

. The operation mode screen in

Figure 4-5-3

appears.

Figure 4-5-3:

Operation Mode Screenshot

4.5.2.1 Disable mode

When selecting disabled operation mode, the device port can be disabled. The disable mode screen in

Figure 4-5-4

appears.

Figure 4-5-4:

Disable Mode Screenshot

Object

Description

•

Apply to all serial

ports

To apply this configuration to all serial ports.

Buttons

: Click to apply port config changes.

When applying any configuration changes of industrial serial server, it’s required to

save changed

configuration and reboot system

. Therefore the new configuration will be applied after rebooting.

«
...
45
46
47
48
49
...
»

Содержание ICS-2100T













































































Отзывы:

Нет отзывов