3
PixelLine6 only
PixelLine4 only
PixelLine2 only
Sets the base DMX address from which the control channels will begin.
Shows the main processor software revision. No changes are possible within
this option. Press while viewing this option to see the software sub-revision.
Shows the display controller software revision. No changes are possible within
this option.
Selects the primary internal chase effect. See Chase effects for descriptions.
Select
MODE
>
EF M
to show the selected chase.
Selects the cross fade speed between the steps of the selected
C1
chase effect.
Selects the speed of the selected
C1
chase effect.
Selects the master intensity level of chase effects
C1
and
C2
.
Selects the secondary internal chase effect. See Chase effects for descriptions.
Select
MODE
>
EF M
to show the selected chase.
Selects the cross fade speed between the steps of the selected
C2
chase effect.
Selects the speed of the selected
C2
chase effect.
Sets the red intensity. Select
MODE
>
MANU
(manual) to show the result.
Sets the green intensity. Select
MODE
>
MANU
(manual) to show the result.
Sets the blue intensity. Select
MODE
>
MANU
(manual) to show the result.
Sets the white intensity. Select
MODE
>
MANU
(manual) to show the result.
Selects number of channels required to control all emitters. Options are 3, 4, 6, 8*, 9*,
12*, 18 or 24. Emitters are grouped together accordingly. * Only on some models.
Determines whether this fixture will act as a master controlling others.
When controlled via DMX this fixture must be set to
SLAV
.
DMX
and
16bt
modes only. When set
ON
this enables the master intensity channel.
The master intensity is always 16bit. For 8bit control use the high (initial) mint channel.
When set
oN
, this option scrolls through the primary colours at power on to
demonstrate correct operation of the emitters.
Determines the intensity of the four digit control panel display. Values range from
0 (dimmest) to 15 (brightest).
When set to
AOFF
, the control panel display will blank out 60 seconds
after the menu is exited. The data dot indicator will remain active.
Provides a choice of two dimmer curves (
FINE
or
TUNG
) to suit particular
circumstances. See next page for descriptions of each option.
RGBW control using an external DMX control input.
PERS
>
MINT
set to
ON
provides
a master intensity in
DMX
and
16bt
modes. No chase effects are selectable.
Displays the resulting RGBW levels that are set via the
MAN
section of the internal
menu. External DMX control is not possible in this mode.
Displays the chase effect(s) determined within the
PROG
section. External DMX
control is not possible in this mode.
DMX Ch1 to 24: RGBW colour mixing, Ch25 to 27:
C1
Effect, Speed & Xfade,
Ch28 to 30:
C2
Effect, Speed & Xfade, Ch31 to 32: Master intensity (16 bit).
DMX Ch1 to 16: RGBW colour mixing, Ch17 to 19:
C1
Effect, Speed & Xfade,
Ch20 to 22:
C2
Effect, Speed & Xfade, Ch23 to 24: Master intensity (16bit).
DMX Ch1 to 8: RGBW colour mixing, Ch9 to 11:
C1
Effect, Speed & Xfade,
Ch12 to 14:
C2
Effect, Speed & Xfade, Ch15 to 16: Master intensity (16bit).
DMX Ch1 to 4: RGBW colour mixing, Ch5 to 7:
C1
Effect, Speed & Xfade,
Ch8 to 10:
C2
Effect, Speed & Xfade, Ch11 to 12: Master intensity (16bit).
16bit RGBW control using 2x the number of DMX channels determined by
PERS
>
RES
.
PERS
>
MINT
set to
On
provides a master intensity. No chase effects are selectable.
Control menu contents
Menu contents are not yet confirmed
