General set up
Mount the fixture in the required position. The integral yoke can
act as a floor stand or hanger.
Important
• When suspended off ground, always use a safety wire rated
to a minimum of 11kg (25lbs) around the yoke.
• Do not position the fixture close to fog machines. The fog oil
mist will be drawn in by the cooling fan and will short out
important components. The warranty will be void for all
fixtures returned in such a condition.
2
Where external control is to be used, connect a DMX lead (XLR
5-pin female) to the input socket at the rear of the fixture.
3
Where other fixtures are to be used in a control daisy-chain, con-
nect a DMX lead (XLR 5-pin male) to the output socket at the rear
of the fixture.
When suspended
off ground, always
use a safety wire
rated to a minimum
of 11kg (25lbs)
around the yoke
User Manual
PixelLine Micro W
User Manual
5
Use the control panel to access the internal menu and choose
the appropriate operation mode and related settings (see over).
4
Connect power to the fixture using a Neutrik
®
PowerCon
®
connec-
tor. Insert the connector and twist it clockwise until it clicks into
place.
Important
• When daisy-chaining fixtures, do not exceed a total load of
3kW in a single daisy chain (subject to supply and cabling
restrictions). Maximum power requirements per fixture:
Micro Wash units - 66 watts. See also the ‘Start up (peak)’
note on page 4.
MENU
ENTER
www
.pixelrange.com
*R
efe
r to
pr
odu
ct m
anu
al f
or
pro
per
op
era
ting
ins
tru
ctio
ns
DOW
N
UP
DMX in
(XLR 5pin
male)
socket
DMX out
(XLR
5pin female)
socket
MENU
ENTER
www
.pixelrange.com
*R
efe
r to
pr
odu
ct m
anu
al f
or
pro
per
op
era
ting
ins
tru
ctio
ns
DOW
N
UP
Power in
socket
Neutrik
®
PowerCon
®
(NAC3FCA)
connector
Power out socket
(Neutrik
®
PowerCon
®
NAC3FCB connector
required)
Fuse holder
(on underside, see
page 4 for details)
Operation modes
The PixelLine Micro Wash fixture provides a range of operation
modes. These are selected using the
MODE
section of the control
menu:
DMX
Allows RGBA control via DMX input. Using the
RES
(resolution) option you can determine the number of
DMX channels required: either 3 or 4 channels. In 3
channel mode, the red and amber channels are com-
bined, whereas in 4 channel mode, the red and amber
channels are controlled separately. Internal chase ef-
fects are not available within this mode.
MANU
Provides RGBA colour mixing independently of any
external control. Use the internal control menu (
MAN
section) to select the required colour values.
EF M
Allows the display of the dual internal chase effects,
independently of any external control. Use the internal
control menu (
PROG
section) to select the required
chase effects, speeds and cross fades.
4+E
Provides control of RGBA mixing and selection of the
dual internal chase effects via DMX input. Requires 11
DMX channels.
PixelLine Micro fixture personalities are available for a variety of
controllers. Please see
www.pixelrange.com
for details.
N
L
Live
Neutral
Earth
Neutrik
®
PowerCon
®
(NAC3FCA) connector
wiring
Note
• To optionally clear all previous settings: At the rear panel,
press the middle two buttons ( and ) while the DMX
address is displayed (e.g.
A001
,
A002
, etc). The four digit
display will show
FACT
then
SET
to indicate that the fixture
has been returned to its default condition.
Version 1.01 firmware
Version 1.01 firmware
