Pitney Bowes SE-900-EI Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 37

Pitney Bowes SE-900-EI Скачать руководство пользователя страница 7

Pitney Bowes

Direct Mail Solutions

Section 3

6

Pitney Bowes DMS

Operation Instructions

1. Adjust the 3-leg sensor arm to position the sensor 1/2” above the paper path

and about 3/4 of the length of the piece ahead of the feeder.

2. With the power still off, turn the speed control counter-clockwise to the

minimum position.

3. Turn the power switch on and turn the speed control switch clockwise, the

first piece will advance until the sensor is blocked and the feeder stops. If the
sensor is not positioned properly, the feeder will not stop. Adjust the height
and angle of the sensor until the feeder stops.

4. Cycle the feeder by removing the piece that blocks the sensor. Observe the

consistency in which the material is feeding.

5. By turning the separator knob slightly in either direction, you will change the

way the material is separating.

6. By moving the back guide in and out, you will quickly find the position, which

creates the most consistent separation.

7. One important item to note; There is no substitution for experience. By

working with the SE 900 EI, you will notice that the combination of separator
setting and the back guide adjustment together will have the greatest effect
on separation. Generally, the longer the piece of material, the flatter the
material stack should be. Conversely, the shorter the piece of material, the
closer the back guide adjustment should be to the material, adding wedge to
the material stack. You will also notice that by moving the back guide forward
(increasing the wedge), you can open the separator and still achieve good
separation.

«
...
5
6
7
8
9
...
»

Содержание SE-900-EI






































Отзывы:

Нет отзывов