Pioneer SC-LX73, Руководство по эксплуатации

Страница: 12 / 144

Controls and displays 02
12
En
STATUS
– P r ess to check selected r eceive r settings
(page 76).
PHASE CTRL – P r ess to switch on/off Phase Cont r ol
o r Full Band Phase Cont r ol (page 59).
CH LEVEL – P r ess r epeatedly to select a channel,
then use
/
to adjust the level (page 111).
THX – P r ess to select a Home THX listening mode
(page 56).
PQLS – P r ess to select the PQLS setting (page 70).
AUTO/ALC/DIRECT
– Switches between Auto
Su rr ound (page 55), Auto Level Cont r ol, Optimum
Su rr ound mode and St r eam Di r ect mode (page 58).
STEREO
– Switches between ste r eo playback and
F r ont Stage Su rr ound Advance modes (page 57).
STANDARD – P r ess fo r Standa r d decoding and to
switch va r ious modes ( 2 P r o Logic, Neo:6, etc.)
(page 55).
ADV SURR – Use to switch between the va r ious
su rr ound modes (page 57).
SIGNAL SEL
– Use to select an input signal (page 58).
SLEEP – Use to put the r eceive r in sleep mode and
select the amount of time befo r e sleep (page 76).
DIMMER – Dims o r b r ightens the display (page 76).
A.ATT – Attenuates (lowe r s) the level of an analog
input signal to p r event disto r tion (page 75).
SBch
– With this r eceive r ,
SBch
cannot be used.
MCACC – P r ess to switch between MCACC p r esets
(page 58).
HDMI OUT – Switch the HDMI output te r minal
(page 76).
11 LIGHT
P r ess to tu r n on/off the illumination fo r the buttons.
1
12 Remote control operation selector switch
Set to
RECEIVER
to ope r ate the r eceive r ,
TV
o r
SOURCE
to ope r ate the TV o r the sou r ce device.
When this switch is set to
RECEIVER
, the r eceive r can be
cont r olled (used to select the white commands). Also use
this switch to set up su rr ound sound.
13 VOL +/–
Use to set the listening volume.
14 MUTE
Mutes the sound o r r esto r es the sound if it has been
muted (adjusting the volume also r esto r es the sound).
Remote control display
2
Remote control display for infrared signal
transmission (default)
Remote control display for RF two-way
communications
3
1 Remote control operating zone indicator
This indicates which zone the r emote cont r ol is cu rr ently
set to ope r ate. The display indicates the setting of the
MULTI-ZONE ope r ation selecto r switch.
Only when RF two-way communications:
The box display he r e indicates the communication status
between this r emote cont r ol unit and the r eceive r .
(White box with black lette r s): Two-way
communications a r e established and the r eceive r ’s
powe r is on.
Note
1 P r ess and hold in the
LIGHT
button fo r 5 seconds to change the illumination mode 1 o r 2. When set to
LIGHT MODE 2
(default), the
illumination only lights when the r emote cont r ol LIGHT button is p r essed. When switched to LIGHT MODE 1 , the illumination lights wheneve r
buttons a r e ope r ated. Setting
LIGHT MODE 1
will sho r ten the se r vice life of the batte r ies.
2 The display lights when a r emote cont r ol ope r ation is pe r fo r med, then tu r ns off afte r 20 seconds if no othe r ope r ation is pe r fo r med. When in
the Remote Setup mode, the setup is canceled and the display tu r ns off if no ope r ation is pe r fo r med fo r 1 minute (page 78).
3 • This is displayed when an RF adapte r is connected to the r eceive r and pai r ed with the r emote cont r ol. Fo r details, see
Using the RF
communications function
on page 86.
• Depending on the communications envi r onment, two-way communications may not wo r k well and the r emote cont r ol display may not r eflect
the r eceive r ’s status.
MAIN SOURCE IR
iPod/USB
1 2 3 4 5 6
7
MAIN
VIDEO
RCV CTRL RF
AV RECEIVER
1. Adv MCACC
+12.
0dB
1 2 3 4 5 6
8 9 10 11 12
MAIN
SC-LX83_73_DLPW.book 12 ページ ２０１０年５月１９日 水曜日 午後２時７分