Pioneer S-71-K, Руководство по эксплуатации

Страница: 4 / 58

4
En
Attaching and Removing the Grille
This speaker system is provided with a removable grille net.
1 To remove the grille, place your fingers at the outside of
the grille toward the bottom and pull gently outward. Then
do the same at the top to detach.
2 To reattach the grille, hold the speaker grille with the
triangular symbol pointing upward, then align the four pins
on the back side of the grille with the holes in the speaker
and press in firmly.
When using the speaker systems with the grille nets removed,
install the accessory attachment grilles on the speakers. These
will help prevent any unnecessary reflections and provide sound
with smoother, broader qualities.
Connections
This speaker does not include speaker cables used for connecting
to an amplifier.
Connecting the cables
1 Switch off the power to your amplifier.
2 Connect the speaker cables to the input terminals (lower)
on the back of the speaker. For input terminal polarity, red is
positive (+) and black is negative (–).
3 Connect the other ends of the cables to the amp's
speaker output terminals (for more details, refer to your amp
instruction manual).
• Grasp the cap knobs on the lower input terminals and rotate
them to the left (counter-clockwise), insert the speaker cable
wires into the holes in the terminal posts, then tighten the
knobs to secure the short bar as well as the wires.
• You can also connect the speaker’s terminals with a banana
plug. When using a banana plug, first use a small flat-blade
screwdriver or tweezers to remove the cap at the tip of the
input terminal.
• After connecting the plugs, pull lightly on the cables to make
sure that the ends of the cables are securely connected to the
terminals. Poor connections can create noise and
interruptions in the sound.
• If the cables’ wires happen to be pushed out of the terminals,
allowing the wires to come into contact with each other, it
places an excessive additional load on the amp. This may
cause the amp to stop functioning, and may even damage the
amp.
• When using a set of speakers connected to an amplifier, you
won’t be able to obtain the normal stereo effect if the polarity
(
+ , – ) of one of the speakers (left or right) is reversed.
Bi-Wire connections
Bi-wiring requires two cables for each speaker, one for high
frequencies and one for low frequencies. Using separate cables
for the high end and low end improves the sound.
1 Switch off the power to your amplifier.
2 Remove the two short bars.
• In this state, the low-frequency speakers and the higher-
frequency speakers are completely independent. Store the
short bars in a safe place for later use.
• The lower terminals are for the bass, and the upper terminals
are for midrange and treble sounds.
• Connecting the cables with reversed polarity may degrade the
tone seriously. Confirm that the cables are connected
properly.
Bi-Amplification connections
Bi-amping is an even more powerful way of connecting your
speakers. Just as with bi-wiring, the input terminal short bars are
removed, but here the low-frequency terminals are connected to a
separate, dedicated low-frequency amp, and the high-frequency
terminals are connected to a dedicated high-frequency amp.
Attachment g r ille
Short bar connectors
Red terminal (+)
Black terminal (
−
)
CAUTION
These speaker terminals carry HAZARDOUS LIVE
voltage . To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
D3-4-2-2-3_A_En
SPEAKERS OUTPUT
HF
HF
LF
LF
Speaker
Amplifier (rear)
(Only one channel shown)
Speaker (rear): Input panel
SPEAKERS OUTPUT
HF
HF
LF
LF
SPEAKERS OUTPUT
(Only one channel shown) (Only one channel shown)
Amplifier (rear)
(High frequency) Amplifier (rear)
(Low frequency)
Speaker
Speaker (rear): Input panel
S-71_En.fm 4 ページ ２００９年９月１７日 木曜日 午後１時２９分