INST
ALLA
TION MANUAL
MANUEL D’INST
ALLA
TION
<99L00F0P01>
DEH-P47DH
Printed in
Japan
Imprimé
au Japon
<CRD3179-A/JS> UC
Connecting the Units
<ENGLISH>
Note:
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
ational vehicle, truck, or bus, check the battery
voltage.
• To avoid shorts in the electrical system, be sure to
disconnect the
≠
battery cable before beginning
installation.
• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right
≠
speaker leads are common.
• Speakers connected to this unit must be high-
power types with minimum rating of 45 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke or becoming dam-
aged.
• When this product’s source is switched ON, a con-
trol signal is output through the blue/white lead.
Connect to an external power amp’s system remote
control or the car’s Auto-antenna relay control ter-
minal (max. 300 mA 12 V DC). If the car features
a glass antenna, connect to the antenna booster
power supply terminal.
• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do not
connect the blue/white lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.
• To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a possi-
bility of short-circuiting if the leads are not insulat-
ed.
• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same
colors correctly.
• If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
operations. If this is not done, the vehicle battery
may be drained when you are away from the vehi-
cle for several hours. (Fig.1)
Fig. 1
• The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
No ACC position
ACC position
ON
S
T
A
R
T
O
FF
ACC
ON
S
T
A
R
T
O
FF
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
• Cords for this product and those for other products
may be different colors even if they have the same
function. When connecting this product to another
product, refer to the supplied Installation manuals
of both products and connect cords that have the
same function.
7
When not connecting a rear speaker lead to a Subwoofer
Multi-CD player
(sold separately)
+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
Antenna jack
Fuse holder
Yellow
Black (ground)
To vehicle (metal) body.
To lighting switch terminal.
Red
Orange
Connecting cords
with RCA pin plugs
(sold separately)
Blue/white
This product
White/black
White
Green/black
Violet
Violet/black
Gray/black
Gray
Rear
Front
Front
Rear
Subwoofer
Subwoofer
Left speaker
Right speaker
With a 2 speaker
system, connect to
the 2 speakers in
the front or the
rear.
Use this for connections
when you have the separately
available amplifier.
Green
IP-BUS input (Blue)
To system control terminal
of the power amp or
Auto-antenna relay control
terminal (max. 300 mA
12 V DC).
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
To terminal always supplied
with power regardless of
ignition switch position.
Subwoofer output
or Non Fading output
Yellow/black
If you use a cellular
telephone, connect it via the
Audio Mute lead on the
cellular telephone. If not,
keep the Audio Mute lead
free of any connections.
System remote control
Caution:
Connect the supplied connector
without fail. If connectors other
than the one supplied with this
product are used, there is the
possibility that sounds may mute
and memorized information
could be erased.
Power amp
(sold separately)
Fig. 2
