Pioneer MVH-1450UB, Руководство пользователя

Страница: 4 / 88

Selecting a source
1
Press SRC / OFF to cycle between:
TUNER
(tuner)
—
USB
(USB)/
iPod
(iPod)
—
AUX (AUX)
Adjusting the volume
1
Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when re-
moving the front panel.
Note
When this unit
’
s blue/white lead is connected to
the vehicle
’
s auto-antenna relay control termi-
nal, the vehicle
’
s antenna extends when this
unit
’
s source is turned on. To retract the anten-
na, turn the source off.
Use and care of the remote
control
Using the remote control
1
Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1
Slide the tray out on the back of the remote
control.
2
Insert the battery with the plus (+) and minus
(
–
) poles aligned properly.
WARNING
!
Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
!
Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
!
Use one CR2025 (3 V) lithium battery.
!
Remove the battery if the remote control is
not used for a month or longer.
!
There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
!
Do not handle the battery with metallic tools.
!
Do not store the battery with metallic ob-
jects.
!
If the battery leaks, wipe the remote control
completely clean and install a new battery.
!
When disposing of used batteries, comply
with governmental regulations or environ-
mental public institutions
’
rules that apply in
your country/area.
Important
!
Do not store the remote control in high tem-
peratures or direct sunlight.
!
The remote control may not function properly
in direct sunlight.
!
Do not let the remote control fall onto the
floor, where it may become jammed under
the brake or accelerator pedal.
Menu operations identical
for set up menu/function
settings/audio adjustments/
initial settings/lists
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1
Press .
Returning to the ordinary display
Canceling the initial setting menu/set up menu
1
Press BAND / .
Returning to the ordinary display from the list
1
Press BAND / .
Tuner
Basic operations
Selecting a band
1
Press BAND / until the desired band ( F1 , F2 ,
F3 for FM, MW or S1 , S2 for shortwave) is dis-
played.
Recalling preset stations
1
Press
c
or
d
.
!
If
MAN
(manual tuning) is selected in
SEEK
,
you cannot recall preset stations. You need to
select
PCH (preset channel) in SEEK . For de-
tails about the settings, refer to SEEK (left/right
key setting) on the next page.
Manual tuning (step by step)
1
Press
c
or
d
.
!
If
PCH
(preset channel) is selected in
SEEK
,
you cannot tune up or down manually. You
need to select
MAN (manual tuning) in SEEK .
For details about the settings, refer to SEEK
(left/right key setting) on the next page.
Seeking
1
Press and hold
c
or
d
, and then release.
You can cancel seek tuning by briefly pressing
c or d .
While pressing and holding
c
or
d
, you can
skip stations. Seek tuning starts as soon as
you release
c
or
d
.
Note
This unit
’
s AF (alternative frequencies search)
function can be turned on and off. AF should be
off for normal tuning operation (refer to
AF (al-
ternative frequencies search) on the next page).
Storing and recalling stations
for each band
Using preset tuning buttons
1 When you find a station that you want
to store in memory, press one of the preset
tuning buttons (1/
to 6/ ) and hold until
the preset number stops flashing.
2 Press one of the preset tuning buttons
(1/ to 6/ ) to select the desired station.
Switching the RDS display
%
Press .
Program service name
—
PTY information
—
En-
tertainment
—
Frequency
#
PTY information and the frequency appear on the
display for eight seconds.
#
Depending on the band, text information can be
changed.
Operating this unit
4
Section
Operating this unit
En
02