Pioneer FX-MG9107ZT-91/UC, Руководство по обслуживанию

Страница: 72 / 100

FX-MG9107ZT/UC
72
1 2 3 4
1 2 3 4
C
D
F
A
B
E
[5]
Focus Close
S-curve Measurement
COMMAND
Contents
Display
*4) 1TR /4TR / 10TR / 32TR / 100TR
-> -> -> -> ->
9X(8X):91(81)
4 TR
92(82)
10 TR
93(83)
32 TR
94(84)
100 TR
95(85)
CRG Move
96(86)
Single TR *5)
-> -> -> F.AGC Gain T.AGC Gain RF AGC Gain TRK/MIN/SEC
*6)
After pressing the eject key, do not press any other key than [Eject] key, till the disc is ejected.
TR Jump operations except for 100TR Jump continues even after you release the relevant key.
For CRG Move and 100 TR Jump operations, the system goes to the Tracking-Close status, when you release the relevant key.
Upon turning the power Off/ON, the Jump Mode is reset to Single TR(91), and RF AMP Gain setting is reset to 0dB, while the automatic
adjusted values goes back to the initial values.
If you are in the middle of measurement, the measurement is terminated.
Key
[TEXT]
[SEEK UP]
[SEEK DOWN]
[1]
[2]
[5]
[TRAF], [PTY],
[MUTE], [AUTO-P]
Operation
Test Mode
Power ON/OFF
CRG+ / TR Jump+
(Toward outer perimeter)
T. CLS & AGC & Applicable servo / AGC, AGC display switching
RF gain select / Offset adjustment display / T.Balance adjustment /
T. Open
F. Close, S. Curve /Rough Servo & RF AGC / F, T, RF AGC
CRG-/TR Jump-
(Toward inner perimeter)
[SCAN], [AST]
[6]
Jump OFF
Focus Mode Select / Tracking Close / CRG, TR Jump Select
MIN SEC TRK
[TEXT]
Power OFF
MIN SEC TRK
[1]
Tracking Servo
Close
[6]
Focus Mode
Select *2
MIN SEC TRK
[SEEK UP]
CRG+
[SEEK DOWN]
CRG-
[SCAN]
Jump OFF
[2]
Auto Adjustment
Display Select *3
MIN SEC TRK
[TRAF]
Focus Close
& TBAL Adjustment
MIN SEC TRK
MIN SEC TRK
91 91 91 0x 0x 0x xx xx xx
MIN SEC TRK
xx xx xx
MIN SEC TRK
91 91 91
00 00 00
99 99 99 ( )
00 00 00
99 99 99 ( )
00 00 00
99 99 99 ( )
*2)
MIN SEC
00 00
S.Curve
MIN SEC
01 01
F EQ measurement setting Focus Close
MIN
SEC
02 02
-> ->
TRK
00
(99 99 99)
TRK
01
TRK
02
*7)
MIN SEC
?? ?/
S. Curve
MIN SEC
FF FF
C1 error count TRK/MIN/SEC
MIN SEC
xx xx
-> ->
TRK
??
(33
→
0)
TRK
xx
TRK
xx
C2 error count
MIN SEC
xx xx
->
TRK
xx
*1)
MIN SEC
-6dB
MIN SEC
06
06
-12dB TYP
MIN SEC
12 12
-> ->
TRK
TRK
06
TRK
12
-> -> F.Offset Display
*3)
T.Offset Display Original display
Error occurrence time
Start of Measurement (30s) / Interruption of Measurement (max. 30s) /
Display of numbers of C1 & C2 errors (after completion of measurement)
MIN SEC
TRK
99 99 99
[5]
Power ON
(T. Offset adjustment not required)
MIN SEC
TRK
xx xx xx
[2]
RF AMP
Gain select *1
[1]
T. Close & AGC
Applicable Servo
MIN
SEC
TRK
[TEXT]
Power OFF
MIN
SEC
TRK
[5]
RF AGC /Close
RF AGC Factor Display
[6]
T. Close
Applicable Servo
MIN
SEC
TRK
[SEEK UP]
CRG+
[SEEK DOWN]
CRG-
[SCAN]
Jump OFF
[2]
T.Balance Adjustment
T.BAL Factor Display
MIN
SEC
TRK
xx xx xx xx xx xx
MIN
SEC
TRK
xx xx xx xx xx xx
MIN
SEC
TRK
xx xx xx
8x 8x 8x
9x 9x 9x
8x 8x 8x
9x 9x 9x
[1]
F, T, RF AGC
Display Switching *6
MIN SEC TRK
[TEXT]
Power OFF
MIN SEC TRK
[6]
CRG/TR Jump
Count Select *5
[5]
F, T, RF AGC /
RF AGC
MIN SEC TRK
[SEEK UP]
CRG/TR Jump+
*4
[SEEK DOWN]
CRG/TR Jump-
*4
[SCAN]
Jump OFF
[2]
Tracking Open
8x
8x
8x
[TRAF]
Error Count
Switching
*7
xx xx xx xx xx xx
MIN SEC TRK
xx xx xx
MIN SEC TRK
xx xx xx
MIN SEC TRK
xx xx xx
[TEXT]
Power OFF
MIN SEC TRK
9x 9x 9x
[2]
Tracking Open
8x 8x 8x
9x 9x 9x
MIN SEC TRK
xx xx xx
MIN SEC TRK
xx xx xx
[DISC]
Source ON
G3 Servo Test Mode Flow Chart
-
CD MECHANISM TEST MODE
[DISC]+[SEEK UP]
Test Mode In
TRK = 0 (Completion of measurement)
TRK >0 (Between measurement)
MIN SEC
TRK
00 00 00
[TEXT]
Power ON
(T. Offset adjustment required)
Note;
The test mode is not available on this unit.
To enter the test mode, load to the designed unit for test mode and then try.
www. xiaoyu163. com
QQ 376315150
9 9
2
8 9
4 2
9 8
TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com