Pioneer FH-MG6406ZH Q1, Руководство по обслуживанию

Страница: 63 / 86

63
FH-MG6406ZH
[SCAN/RPT]
Power Off
MIN
SEC
[3]
Focus Close/S-curve/
F, F0 Measurement
MIN
SEC
91 91
[5]
Focus Mode Select
MIN SEC
0X 0X
[1]
Tracking Servo
Close
MIN
SEC
00 00
[SCAN/RPT]
Power ON
(T.OFFSET adjustment required)
MIN SEC
00 00
[3]
Power ON
(T.OFFSET adjustment not required)
MIN SEC
99 99
[1]
Mechanism Test Mode
Initial State
MIN SEC
0* **
[5]
New Test Mode
[CD] or [SOURCE]
Source CD
MIN SEC
** **
[SCAN/RPT]
Power Off
[1]
Tracking Close
(AGC, Applicable Servo)
MIN SEC
XX XX
[5]
Tracking Close
(No AGC, Applicable Servo)
MIN SEC
XX XX
[3]
Auto Adjustment Display
/Rough Servo
MIN SEC
?? ??
[2]
Tracking Balance
Adjustment
MIN SEC
8X 8X
[Key]
Contents
Display
[4] + [6] + RESET
Test Mode In
[3]
AGC
MIN SEC
XX XX
[5]
CRG/TR Jump Count
Select
MIN SEC
XX XX
[SEEK/SKIP+]
CRG+/TR Jump+
MIN SEC
XX XX
[SEEK/SKIP-]
CRG–/TR Jump–
MIN SEC
XX XX
[4]
SPINDLE
Uniform/
Double Switching
MIN
SEC
XX XX
[SCAN/RPT]
Power Off
[1]
AGC/F.BIAS
Display Switching
MIN SEC
?? ??
MIN
SEC
99 99
or
[SEEK/SKIP+]
CRG+
MIN SEC
00 00
TRK
MIN
99
99
or
[SEEK/SKIP-]
CRG-
MIN SEC
00 00
MIN
SEC
99 99
or
[SEEK/SKIP+]
CRG+
MIN SEC
8X 8X
MIN SEC
9X 9X
or
[SEEK/SKIP-]
CRG-
MIN SEC
8X 8X
MIN SEC
9X 9X
or
[SCAN/RPT]
Power Off
[2]
Trackig Open
MIN SEC
8X 8X
MIN
SEC
9X 9X
or
[2]
Trackig Open
MIN SEC
8X 8X
MIN SEC
9X 9X
or
*1
*6
*5
*3
*2 *2
*4
*1) Switching must take place in the following sequence.
MIN SEC
00
00
( ) MIN
SEC
99
99
S.Curve Check
MIN SEC
01
01
Focus EQ Measurement. Focus Close
MIN SEC
02 02
*2)
→ → → → →
9X(8X):91(81)
4 TR
92(82)
10 TR
93(83)
32 TR
94(84)
100 TR
95(85)
CRG Move
96(86)
Switching must take place in the following sequence.
*4)
→ → →
F.AGC Gain T.AGC Gain F. BIAS Setting
(AGC Gain = (Current value/Initial value) x 20)
→ → →
→ →
Single TR /4TR / 10TR / 32TR / 100TR
Single TR
*3) Switching must take place in the following sequence.
It applies to the CRG Move and 100TR Jump alone.
Min/Sec (or Track No.)
*5) Switching must take place in the following sequence.
F.Cancel Display
*6) Switching must take place in the following sequence.
T.Offset Display T.Bal Display Rough Servo.
(F.Bias value, F.Cancel value, T.Offset value, T.Bal value
= (Upper 8 bits of the setting (7F[H] to 80[H] + 128)/4
= 63[D] to 32[D] to 00[D]).
•
•
•
Operation of TR JUMPs other than 100TR is continued after your finger has left the key.
CRG Move and 100TR Jump are forced to the Tracking Close Mode when the key is released.
Powering on or off resets the Jump Mode to the Single TR (91).
When ending the test mode, apply the reset (the reset is applied in two minutes from powering off).
Note:
Note:
Sound is unavailable even after the tracking has been closed
(this trouble results when the IC for the STS is not controlled in the test mode).
When you pressed the [SEEK/SKIP+] or [SEEK/SKIP-] key during the Focus Search, you must turn the power off immediately
(otherwise, the lens can stick resulting in actuator damages).
[Key]
[SCAN/RPT]
[SEEK/SKIP+]
[SEEK/SKIP-]
[1]
[2]
[3]
[4]
[5]
[6]
Operation
Test Mode New Test Mode
Power ON/OFF
CRG+/TR Jump+
(Toward outer perimeter)
Tracking Close/AGC gain,
F.Bias adjustment value display switching
Auto Tracking Balance adjustment/
Tracking Open
Focus Close, S.Curve, F.EQ measurement/
Rough Servo/AGC
Focus Open
Focus Mode select/Tracking Close/
CRG*TR Jump Switching
CRG-/TR Jump-
(Toward inner perimeter)
Error occurrence time/
Cause display switching
Track+/FF
Track-/REV
Mode
RAMDOM
Auto/Manual switching
MIN SEC
MIN SEC
MIN SEC
DISC UP
DISC UP
[EJECT]
[LOAD]
DISC Eject DISC Eject
DISC Load DISC Load
RPT
-
CD Player Flowchart