20
PD-D6MK2-K
1
2
3
4
A
B
C
D
E
F
1
2
3
4
No.
Symptoms
Diagnosis Contents
Possible Defective Points
1
The power is not turned on. Are wires of output connector (POWER SUPPLY Unit) and C
N
901
(D
V
DM Assy) disconnected or damaged ?
Connector / cable
Check that the following voltage is output :
+ side of C739 : 3.3
V
DVDM Assy
3.3
V
Regulator IC (IC341)
2
An opening screen is not
displayed on the monitor
(The FL display lights. The
mechanism does not work.)
Are the signals output from IC201-pin 9
8
(MDATA) and pin 99 (SCLK)
on the D
V
DM Assy ? (in the range of 0-3
V
)
DVDM Assy
D
V
D IC (IC201)
Are the signals input into IC2101-pin 50 (MDATA) and pin 51 (SCLK)
on the LCD Assy ? (in the range of 0-3
V
)
LCD Assy
UCOM (IC2101)
Check that the following voltage are output :
IC751-pin 1 on the D
V
DM Assy : 5
V
DVDM Assy
5
V
Regulator IC (IC751)
Is a resonator (X202: 27MHz) on the D
V
DM Assy oscillating ?
DVDM Assy
Crystal resonator (X202)
• Is a signal input into IC203-pin26 (PCE#) on the D
V
DM Assy ?
(Is a signal "H" for
8
0 mS and then "L" after the power is turned
on ?)
→
Communication with flash ROM.
• Are the signals input into IC202-pin 16 (DWE#), pin 19 (DCS#)
and pin 3
8
(SDCLK) on the D
V
DM Assy ?
(Is a signal fluctuating ?)
→
Communication with SDRAM
DVDM Assy
D
V
D IC (IC201)
Flash ROM (IC203)
SDRAM (IC202)
Is a signal output from IC203-pin 2
8
(PRD#) on the D
V
DM Assy?
(Is a signal fluctuating for several hundred mS after the power is turned
on ?)
DVDM Assy
Flash ROM (IC203)
Is a signal input into IC2101-pin 67 (D
V
D ACK) on the LCD Assy ?
(Is a signal fluctuating ?)
→
Communication with FL Control IC
DVDM Assy
D
V
D IC (IC201)
LCD Assy
UCOM (IC2101)
Is a signal output from IC2101-pin 30 (XREADY) on the LCD Assy ?
(Is a signal fluctuating in the range of 0-5
V
?)
LCD Assy
UCOM (IC2101)
Are the signals output from IC2101-pin 49 (SDATA) on the LCD Assy ?
(in the range of 0-5
V
)
DVDM Assy
D
V
D IC (IC201)
LCD Assy
UCOM (IC2101)
Are the signals of IC204-pin 5(SDA) and pin 6(SCL) on the D
V
DM Assy
fluctuating for one or two seconds after the power is turned ?
DVDM Assy
EEPROM (IC204)
Addendum
N
o.1
A tray cannot be opened.
(An opening screen is
displayed on the monitor)
LOAB Assy
Tray SW (S101)
Is the signal input into IC101-pin 11 (TROPE
N
) on the D
V
DM Assy ?
V
, At close: 0
V
DVDM Assy
D
V
D IC (IC201)
Are the signals output from IC101-pin 1 and pin 2 (C
N
103-pin 1 and
V
DM Assy ?
Pin 2: Approx. 6
V
during opening tray approx. 0
V
during closing tray.
Pin 1: Approx. 0
V
during opening tray approx. 6
V
during closing tray.
DVDM Assy
FTS Driver IC (IC101)
Are wires of C
N
104 and C
N
103 on the D
V
DM Assy disconnected or
damaged ?
Connector / cable
Does the voltage of C
N
102-pin 1 on the D
V
DM Assy change to 0
V
by
pressing the Inside switch.
Inside switch
N
104-pin 3 and pin 5 on the D
V
DM Assy change
N
)): Tray is fully closed: "L"
Pin 5 (SW1(TROUT)): Tray is fully opened: "L"
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
