60
15 cm (6 in.) dia.
or more
Condensation
Moisture may form in the operating section of the player
if the player is brought from cool surroundings into a
warm room or if the temperature of the room rises
suddenly. When this happens, the player’s performance
will be impaired.
To prevent this, let the player stand in its new
surroundings for about an hour before switching it on, or
make sure that the room temperature rises gradually.
Condensation may also form during the summer if the
player is exposed to
the breeze from an air
conditioner. In such
cases, change the
location of the player.
Switch POWER to STANDBY when not using
the unit
Depending on the strength of the TV or radio broadcast
signal, having the TV or radio on while
power to the unit is on may result in
stripes on the TV screen or noise.
However, this is not a malfunction of
this unit or the TV or radio. In such a
case, switch the power of the unit to
standby.
Power-cord caution
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power cord
when your hands are wet as this could cause a short
circuit or electric shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the cord.
Never make a knot in the cord or tie it with other cords.
The power cords should be routed in such a way that
they are not likely to be stepped on. A damaged power
cord can cause a fire or give you an electrical shock.
Check the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized service
center or your dealer for a replacement.
Cleaning the player
To clean the PLAYER, wipe with a soft, dry cloth. For
stubborn dirt, wet a soft cloth with a mild detergent
solution made by diluting one part detergent to 5 or 6
parts water, wring well, then wipe off the dirt. Also use a
dry cloth to wipe the surface dry. Do not use volatile
liquids such as benzene and thinner which are harmful to
the unit.
Notes on using optical cables
• Do not route cords around sharp angles. When storing,
wind the cords so that they have a
diameter of at least 15 cm (6 in.).
• When connecting, push all the way
into the terminal.
• Do not use cords with a length of
over 3 m.
• If moisture or dust has collected on
the plug, wipe it with a soft cloth
before connecting.
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong
with this component, check the points below.
Sometimes the trouble may lie in another component.
Inspect the other components and electrical appliances
being used. If the trouble cannot be rectified even after
exercising the checks listed below, ask your nearest
PIONEER authorized service center or your dealer to
carry out repair work.
The disc table comes back out automatically, shortly
after the disc table is closed.
The disc is dirty or warped.
\
Refer to
‘Disc Care’
(
page 59
).
The disc is not placed properly on the disc table.
\
Use the disc table guide to align the disc (
page 22
).
Region number does not conform with this unit.
\
If the region number on the disc does not match
the number on the player, the disc cannot be used
(
page 63
).
There is condensation on the operating section of the
player.
\
Allow time for condensation to evaporate. If player
is near an air conditioning unit, you should move
the player (
page 60
).
Playback is not possible.
The disc has been loaded upside down.
\
Check that the disc has been loaded with the label
side facing up.
mark appears on screen.
The selected function does not operate for that disc.
mark appears on screen.
The operation is prohibited by the player.
Picture playback stops and the operation buttons
cannot be used.
Player malfunctions.
\
Stop disc playback (press
STOP
7
), then start
playback again.
New settings made in the Setup screen menus while
a disc is playing are ineffective.
Some settings can be changed while a disc is playing,
but are not effective. This is not a malfunction.
\
Make the same setting when the player is
stopped.
\
Stop disc playback (press
STOP
7
), then start
playback again. When playback is resumed, the
new settings should be in effect. Please note that
making settings in the Setup screen menus may
cancel the resume function.
When making changes in the Setup screen menus,
is displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\
The setting will be effective the next time a DVD
is loaded.
Содержание Elite DV-37
Страница 1: ...DV 37 Operating Instructions DVD PLAYER ...
