Pioneer DVR-RT602H-S, Руководство по обслуживанию

Страница: 97 / 174

DVR-RT602H-S
97
5 6 7 8
5 6
7
8
C
D
F
A
B
E
1-4: CONFIRMATION OF VSR TORQUE
1. Install the Torque Gauge ( GGF1508 ) and Adapter
( GGF1506 ) on the S Reel. Set to the Picture Search
(Rewind) mode. ( Refer to Fig.1-4-B )
2. Then, confirm that it indicates 120~180gf•cm.
NOTE
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) ( Refer to Fig. 1-4-B )
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of
Fig. 1-4-A .
2. Move the Idler Assy from the S Reel.
3. Install the Torque Gauge (
GGF1508 ) and Adapter
( GGF1506 ) on the S Reel. Turn the Torque Gauge
( GGF1508 ) clockwise.
4. Then, confirm that it indicates 60~100gf•cm.
(T Reel Brake) ( Refer to Fig. 1-4-B )
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of
Fig. 1-4-A .
2. Move the Idler Assy from the T Reel.
3. Install the Torque Gauge (
GGF1507 ) and Adapter
( GGF1506 ) on the T reel. Turn the Torque Gauge
( GGF1507 ) counterclockwise.
4. Then, confirm that it indicates 30~50gf•cm.
NOTE
If the torque is out of the range, replace the following parts.
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and
adjustment are necessary.
2-1: GUIDE ROLLER
1. Playback the VHS Alignment Tape ( GGV1222 ).
( Refer to SERVICING FIXTURE AND TOOLS )
2. Connect CH-1 of the oscilloscope to TP101 ( Envelope )
and CH-2 to TP3002 ( SW Pulse ).
3. Press and hold the ATR button on the remote control
more than 2 seconds to set tracking to center.
4. Trigger with SW Pulse and observe the envelope.
( Refer to Fig. 2-1-A )
5. When observing the envelope, adjust the Adjusting
Driver ( GGF1509 ) slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
6. Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B , even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
7. Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
The position at FF mode.
Stop at this position.
The position at
STOP mode.
Caption
DD Unit
Cassette
Opener
Pinch Roller Block
Cassette Holder Assy
S Reel
T Reel
Torque Gauge/Adpter
(GGF1508/GGF1506)
Torque Gauge/Adpter
(GGF1507/GGF1506)
CH-1
Envelope
(TP101)
CH-2
SW Pulse (TP3002)
Max Max
A : B 3 : 2
Entrance Exit
CH-1
Track
CH-2
Track
Fig. 1-4-A
Fig. 2-1-A
Fig. 2-1-B
Fig. 1-4-B
Check Item Replacement Part
1-4 Idler Assy / Clutch Assy
1-5
S Reel side : S Reel/ Tension Band/Tension
Connect/Tension Arm Assy
T Reel side : T Reel/ Brake Band/T Brake Spring
/T Brake Arm
A B