Pioneer DV-C603, Руководство по эксплуатации

Страница: 57 / 64

57
ADDITIONAL INFORMA
TION
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong
with this component, check the points below.
Sometimes the trouble may lie in another component.
Inspect the other components and electrical appliances
being used. If the trouble cannot be rectified even after
exercising the checks listed below, ask your nearest
PIONEER authorized service center or your dealer to
carry out repair work.
The disc table comes back out automatically, shortly
after the disc table is closed.
The disc is dirty or warped.
\
Refer to ‘Disc Care’ ( page 54 ).
The disc is not placed properly on the disc table.
\
Use the disc table guide to align the disc ( page 21 ).
Region number does not conform with this unit.
\
If the region number on the disc does not match
the number on the player, the disc cannot be used
(
page 60 ).
There is condensation on the operating section of the
player.
\
Allow time for condensation to evaporate. If player
is near an air conditioning unit, you should move
the player (
page 55
).
Playback is not possible.
The disc has been loaded upside down.
\
Check that the disc has been loaded with the label
side facing up.
The disc is not aligned in the disc tray properly.
\
Open the disc tray and make sure that the disc is
aligned correctly.
mark appears on screen.
The selected function does not operate for that disc.
mark appears on screen.
The operation is prohibited by the player.
Picture playback stops and the operation buttons
cannot be used.
Player malfunctions.
\
Stop disc playback (press STOP
7
), then start
playback again.
New settings made in the Setup screen menus while
a disc is playing are ineffective.
Some settings can be changed while a disc is playing,
but are not effective. This is not a malfunction.
\
Make the same setting when the player is
stopped.
\
Stop disc playback (press STOP
7
), then start
playback again. When playback is resumed, the
new settings should be in effect. Please note that
making settings in the Setup screen menus may
cancel the resume function.
When making changes in the Setup screen menus,
is displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\
The setting will be effective the next time a DVD
is loaded.
Settings are canceled.
When the power is turned off by power failure or by
unplugging the power cord, settings will be canceled.
\
Before unplugging the power cord, press
STANDBY/ON and check that “--OFF--”
disappears in the display.
No picture.
The rear panel’s VIDEO OUT SELECT switch setting
is not correct.
\
Check that the VIDEO OUT SELECT switch is set
to the correct position for the monitor connection
you are using (
page 17 ).
Connection is incorrect.
\
Check that cord connections are correct and that
plugs are firmly connected.
Operation (settings) of TV or AV amplifier is not
appropriate.
\
Be sure that your TV, receiver, or amplifier is set
up to view DVD playback.
The [Component Video] menu is set to
[Progressive] but your TV/monitor is not compatible
with progressive scan.
\
Reconnect the player to your TV using a
composite or S-video cord, then set the
VIDEO
OUT SELECT switch on the rear panel to
COMPOSITE & S-VIDEO . With your TV
connected using either the composite or S-Video
terminals, choose the
[Interlace] setting in the
[Component Video] menu, then set the rear
panel switch back to COMPONENT ( page 32 ).
\
Reset the player (
page 53
). [Component Video]
will be reset to [Interlace] but you’ll also loose
other settings.
The screen is stretched or aspect does not change.
The multi aspect setting is not appropriate.
\
Change the aspect setting in the [TV Screen]
setting in the Setup screen Video menu to the
screen type most appropriate to the TV or monitor
you are using (
page 30 ).
If you connected your TV with an S-Video cord, in rare
cases the TV picture may appear stretched.
\
Change the [S-Video Out] setting to [S1] ( page
33 ).
This is not a malfunction.
\
The aspect ratio of some progressive-scan
compatible TVs cannot be changed.
Picture disturbance during playback or dark.
(Interlace/Progressive-scan)
This is not a malfunction.
\
This player is compatible with Macro-Vision
System copy guard. Some discs include a copy
prevention signal, and when this type of disc is
played back, stripes etc., may appear on some
sections of the picture depending on the TV.
When using progressive-scan.
\
If your TV is connected using the COMPONENT
VIDEO OUT jacks, set the [Component Video]
menu to [Interlace] ( page 32 ).