DJM-909
126
1
2
3
4
1
2
3
4
C
D
F
A
B
E
• When Initial Setting mode for the noncontact fader is activated, "DJM-909 FADER SET MOVE CROSS FADER FROM A LEFT END TO A
RIGHT END PUSHING CH1 FADER START KEY" is displayed on the LCD.
How to set up
1
Move the crossfader lever to the leftmost position.
2
While holding the CH1 FADER START button pressed, move the crossfader lever to the rightmost position.
Move the lever at a constant speed from the leftmost to the rightmost position, taking 1.5 seconds or more.
3
Release the CH1 FADER START button.
• When the initial setting is completed, "END" is displayed on the LCD, and the CH-1 FADER START and C.F.1 FADER START indications
light up.
• If the initial setting fails, "ERROR" is displayed on the LCD, and the CH-1 FADER START, C.F.1 FADER START, CH-2 FADER START, or
C.F.2 FADER START indication flashes, depending on the type of error.
If an error is generated, repeat from Step
1
of "How to set up."
• When the initial setting for the noncontact fader is completed, press the CH2 FADER CURVE/ BANK EDIT button to return to the menu of
Setup mode. You can proceed to Calibration mode for the touch panel.
3. Setup mode
To enter Setup mode, while holding both the CH1 FADER START and CH2 FADER START buttons pressed, press the POWER button.
Setup Mode : ON
Setup Mode : CANCEL
Release
SERVICE MODE
CH1 FADER START
CH2 FADER START
POWER OFF
POWER OFF
POWER ON
Fader Setup Mode : ON
Fader Setup Mode : CANCEL
Release
CH1 FX ADJ.
POWER OFF
• When Setup mode is activated, "DJM-909 SETMODE" is displayed on the LCD.
During Setup mode, if the CH1 FX ADJ. button is pressed, Initial Setting mode for the noncontact fader is activated.
During Setup mode, if the CH1 FADER CURVE/ BANK EDIT button is pressed, Calibration mode for the touch panel is activated.
During Setup mode, if the CH2 FX ADJ. button is pressed, Factory-Preset Effect mode is activated.
4. Initial Setting mode for the noncontact fader
To enter this mode, press the CH1 FX ADJ. button during Setup mode. (For details on how to enter Setup mode, see "3. Setup mode.")
LED
Error
CH-1 FADER START
Start error: At the start of making the initial setting, the crossfader lever was not set to its leftmost position.
C.F.1 FADER START
Speed error: The crossfader lever was moved too quickly.
CH-2 FADER START
End error: The crossfader lever was not moved to its rightmost position.
C.F.2 FADER START
Code error: The gray codes for the crossfader could not be read.
DJM-909
FADER SET
MOVE CROSS FADER
FROM A LEFT END
TO A RIGHT END
PUSHING
CH1FADER START KEY
TO MENU
DJM-909
SET MODE
CAL IBRATION
FADER SET
RESET
Содержание DJM 909 - Battle Mixer W/Effects
