Black plate (4,1)
Note
When this unit
’
s blue/white lead is connected to
the vehicle
’
s auto-antenna relay control termi-
nal, the vehicle
’
s antenna extends when this
unit
’
s source is turned on. To retract the anten-
na, turn the source off.
Use and care of the remote
control
Using the remote control
1
Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1
Slide the tray out on the back of the remote
control.
2
Insert the battery with the plus (+) and minus
(
–
) poles aligned properly.
WARNING
!
Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
!
Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
!
Remove the battery if the remote control is
not used for a month or longer.
!
There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
!
Do not handle the battery with metallic tools.
!
Do not store the battery with metallic ob-
jects.
!
If the battery leaks, wipe the remote control
completely clean and install a new battery.
!
When disposing of used batteries, comply
with governmental regulations or environ-
mental public institutions
’
rules that apply in
your country/area.
Important
!
Do not store the remote control in high tem-
peratures or direct sunlight.
!
The remote control may not function properly
in direct sunlight.
!
Do not let the remote control fall onto the
floor, where it may become jammed under
the brake or accelerator pedal.
Frequently used menu
operations
Returning to the previous display
Returning to the previous list (the folder one level
higher)
1
Press
/
DIMMER
.
Returning to the ordinary display
Canceling the main menu
1
Press
BAND
.
Returning to the ordinary display from the list
1
Press
BAND
.
Radio
Basic operations
Selecting a band
1
Press
BAND
until the desired band (
FM1
,
FM2
,
FM3
for FM,
MW
or
SW1
,
SW2
for short-
wave) is displayed.
Switching preset stations
1
Press
c
or
d
.
!
Select
PCH
(preset channel) under
SEEK
to
use this function.
!
Use the
a
and
b
on the remote control to
switch between preset stations.
Manual tuning (step by step)
1
Press
c
or
d
.
!
Select
MAN
(manual tuning) under
SEEK
to
use this function.
Seeking
1
Press and hold
c
or
d
, and then release.
You can cancel seek tuning by briefly pressing
c
or
d
.
While pressing and holding
c
or
d
, you can
skip stations. Seek tuning starts as soon as
you release
c
or
d
.
Notes
!
For details about
SEEK
, refer to
!
This unit
’
s AF (alternative frequencies
search) function can be turned on and off.
AF should be off for normal tuning operation
(refer to
(alternative frequencies search)
Storing and recalling stations
for each band
Using preset tuning buttons
1
To store: Press and hold down one of the
preset tuning buttons (1/
to 6/
) until
the number stops flashing.
2
To recall: Press one of the preset tuning
buttons (1/
to 6/
).
Switching the display
Selecting the desired text information
1
Press
DISP
/
DISP OFF
to cycle between the fol-
lowing:
!
FREQUENCY
(program service name or
frequency)
!
BRDCST INFO
(program service name/PTY
information)
!
CLOCK
(source name and clock)
Notes
!
If the program service name cannot be ac-
quired in
FREQUENCY
, the broadcast fre-
quency is displayed instead. If the program
service name is detected, the program serv-
ice name will be displayed.
!
Depending on the band, text information can
be changed.
!
Text information items that can be changed
depend on the area.
Using PTY functions
You can tune in to a station using PTY (program
type) information.
Using this unit
4
Section
Using this unit
En
02
<QRB3345-A>4
