Installation
English
Installation
English
Note
•
Check all connections and systems before final
installation.
•
Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
•
Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
•
Do not install this unit where:
—
it may interfere with operation of the vehicle.
—
it may cause injury to a passenger as a result
of a sudden stop.
•
The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
•
Optimum performance is obtained when the unit is
installed at an angle of less than 60°.
60
°
•
When installing,
to
ensure proper heat dispersal when using this unit,
make sure you leave ample space behind the rear
panel and wrap any loose cables so they are not
blocking the vents.
10cm (3-7/8 in.)
Leave ample space
Dashboard
10cm (3-7/8 in.)
•
The cords must not cover up the area shown in
the figure below. This is necessary to allow the
amplifires to radiate freely.
Do not cover this area.
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
Removing or attaching
the trim ring
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring.
•
When reattaching the trim ring, push the trim
ring onto the unit until it clicks. (If the trim
ring is attached upside down, the trim ring will
not fit properly.)
•
It becomes easy to remove the trim ring if the
front panel is released.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screws and holders.
1. Attach the holders to both sides of
the front panel.
2. Replace the front panel to the unit.
3. Flip the holders into upright
positions.
4. Fix the front panel to the unit using
screws.
Installing the microphone
Installation notes
Install the microphone in a position and
orientation that will enable it to pick up the
voice of the person operating the system.
CAUTION
• It is extremely dangerous to allow the microphone
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
on the sun visor
1. Install the microphone on the
microphone clip.
2. Install the microphone clip on the
sun visor.
• With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the
recognition rate for voice operations.)
Factory radio mounting bracket
Screw
Dashboard or Console
Installation
English
DIN Front-mount
Installation with the rubber bush
1. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
53
53
1
1
182
182
2. Install the unit as illustrated.
Removing the Unit
1. Insert the supplied extraction keys
into both sides of the unit until
they click into place.
2. Pull the unit out of the dashboard.
DIN Rear-mount
1. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
2. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Dashboard
Mounting sleeve
Rubber bush
Screw
Trim ring
Microphone
Microphone clip
Microphone clip
Clamps
Use clamps to secure
the lead where
necessary inside the
vehicle.
When installing the microphone
on the steering column
1. Install the microphone on the
microphone clip.
2. Install the microphone clip on the
steering column.
Adjusting the microphone
angle
The microphone angle can be adjusted by
moving forward or backward the microphone
clip angle.
Microphone
Microphone clip
Fit the
microphone lead
into the groove.
Double-sided tape
Install the microphone clip on the
rear side of the steering column.
Clamps
Use clamps to secure
the lead where
necessary inside the
vehicle.
Screw
Installation
English