background image

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 6)

Fig. 6

Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly as possible using the
top and bottom tabs. To secure, bend
the tabs 90 degrees.)

182

53

Rubber bush

Screw

Dashboard

Installation

Note:

• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts
can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications
of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot 
— for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the Head Unit might not give its optimum perfor-
mance. (Fig. 5)

Fig. 5

• When mounting this unit, make sure none of the

leads are trapped between this unit and the sur-
rounding metalwork or fittings.

• Do not mount the tuner unit near the heater outlet,

where it would be affected by heat, or near the
doors, where rainwater might splash onto it.

• Before drilling any mounting holes always check

behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.

• If the tuner unit is installed in the passenger com-

partment, anchor it securely so it does not break
free while the car is moving, and cause injury or an
accident.

• If the tuner unit is installed under a front seat,

make sure it does not obstruct seat movement.
Route all leads and cords carefully around the slid-
ing mechanism so they do not get caught or
pinched in the mechanism and cause a short cir-
cuit.

60

°

Removing the Unit (Fig. 7) (Fig. 8)

Fig. 7

Fig. 8

5

6

Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)

Frame

Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.

Содержание DEH-P3370XM UC

Страница 1: ... If the car features a glass antenna connect to the antenna booster power supply terminal When an external power amp is being used with this system be sure not to connect the blue white lead to the amp s power terminal Likewise do not connect the blue white lead to the power terminal of the auto antenna Such connection could cause excessive current drain and malfunction To avoid short circuiting c...

Страница 2: ...t of this unit is monaural Red To electric terminal controlled by ignition switch 12 V DC ON OFF Black ground To vehicle metal body Yellow To terminal always supplied with power regardless of ignition switch position To Tuner unit Refer to Fig 2 Orange white To lighting switch terminal Blue white To system control terminal of the power amp or Auto antenna relay control terminal max 300 mA 12 V DC ...

Страница 3: ... t install the unit anywhere hot for instance near a heater outlet If installation angle exceeds 60 from horizontal the Head Unit might not give its optimum perfor mance Fig 5 Fig 5 When mounting this unit make sure none of the leads are trapped between this unit and the sur rounding metalwork or fittings Do not mount the tuner unit near the heater outlet where it would be affected by heat or near...

Страница 4: ... DIN Rear mount Installation using the screw holes on the side of the unit 1 Remove the frame Fig 9 Fig 9 2 Fastening the unit to the factory radio mounting bracket Fig 10 Fig 11 Select a position where the screw holes of the bracket and the screw holes of the head unit become aligned are fitted and tighten the screws at 2 places on each side Use either truss screws 5 8 mm or flush surface screws ...

Отзывы: